So I rebuilt my 3F carburetor this weekend. Pinhead’s videos on YouTube was quite helpful, almost as much as the factory manual. The problem is, now after the rebuild, the cruiser would not idle.
This is a GCC-spec FJ75 with a GCC-only idle speed screw, which is made so that it cannot be...
I have a 12V overhead console for an 80 series with altimeter and second subtank fuel gauge for sale. It came from an Australian market 80 series.
It is in good condition. I tested the dome light, but I was unable to test the fuel gauge as I do not have an 80 series wiring diagram.
$200 + USPS...
Hey guys, after for 14 years I’ve come back to Land Cruisers. The trucks have been sitting in the garage and finally it’s time to move them as we are moving from CA to UT.
So I am trying to bring this FJ 75 with 3F engine back to life. I believe the ignition coil is dead since the secondary...
Does anyone here have weight info for the 1990-1995 75 series pick up?
I need the GVWR (gross vehicle weight rating) and the GAWR (gross axle weight rating) for the front and rear.
Thanks!
Posting this as a new thread to make it easier to search.
My 1HDT has been clicking loudly from the area of the fuel pump when it is cold. When the engine is at normal operating temp, the clicking disappeared. Dana Adams told me his had the same problem and he disabled his Assist(?) Cold Start...
Before I go through a deal with a fellow club member, please let me know if I am
selling what I think. He is buying two third members from me, one is a factory
LSD and the other is an open diff:
Question: Does the diff on top look like it can fit a semifloater cruiser rear
axle...
Interesting finding a local cruiserhead found on eBay:
2.8L intercooled turbo diesel that fits a standard Chevy small block bellhousing pattern. Seems that these engines are brand new and built to order. 135 hp but can be cranked up to 170 hp.
Note the pics are not of the engines.
Dave
Kiwimidi, in your post to Readers Rides, you said you have a CT26 hybrid turbo in your BJ74. Care to tell us about it? Do you get a higher output, better spool up, etc.?
The spring over conversion looks good, BTW.
Dave
Hi Fred,
Welcome to the board! I notice the 73 and 75 series landcruisers that were sold in Belgium and the Netherlands have blanked out rear side windows. Is this so that they could be classified as a van instead of a passenger vehicle or a bus?
Dave
Most of us are familiar with the IFS Hilux front hub conversion to gain an extra 3" of axle width on our cruiser front axle. Aseif007 and I have been discussing how to narrow a late/US model 80 series rear axle to get it to match his front 60 series axle width. So I am posting this to share...
Have a look at the dashboard on this 1993 KZJ70:
It looks as if the instrument cluster, steering wheel column and the metal part underneath is not changed from the model that debuted in 1985, but the top upholstered part sure looks nice IMO.
This is what the vehicle looks like:
so...
Has anyone here used gearless ratchets, such as the one made by Mac Tools? What attracted me to it is the ability to ratchet in less than 5 degrees. What's your impression? Would you buy it again? Would you recommend it?
Dave
Booster and 1" bore brake master cylinder off my 1975 FJ40. Worked fine when I had 4 wheel drums, taken off for a 4 wheel disc conversion. I will also throw in a functional clutch master from the same vehicle, but the rubber cap shows cracking from age.
Bsically I'm giving it away but I'm...
Repost from POR:
http://cgi.ebay.com/ebaymotors/Toyota-Land-Cruiser-Diesel-w-Factory-F-R-Locking-Diffs_W0QQitemZ4585771116QQcategoryZ6443QQrdZ1QQcmdZViewItem
The seller has sold two Town Aces and an HJ61 licensed in Washington State with positive feedbacks.
Time to put up money where...
Fitting cable lockers to my cruiser. Question for those who have a long wheel base cruiser with factory cable lockers (such as the HJ60 or HJ61): Does the rear cable go next to the fuel tank or does it run along the frame rail? Thanks,
Dave
I bought this transfer case from another guy in this forum. I'm in the process of rebuilding it and I noticed the high range idler gear is pitted like this:
About 2/3rd of the teeth on the gear are pitted. The input and output gears and the low range idler gear are in good shape...
I'm selling an H151f 5 speed transmission to fit an FZJ80. It comes with a fulltime transfer case, bellhousing, clutch, pressure plate, throw out bearing, clutch pedal assembly including pedal hanger, a clutch master and the transmission wiring harness. I'm asking for $2950.00 for it...
Been thinking of a set of vehicle dollies, those metal plates with casters, to move my other cruiser around in storage. Any recommendations? I need to move it around mostly side to side, to get to parts on the other side, etc. The cruiser in storage has no driveshaft so it is not moving under...