Search results for query: *

  • Users: arndog
  • Content: Threads
  • Order by date

Forum search Google search

  1. A

    roof "rack" bolts

    I don't have a roof rack on my 80 but I do have what I would call rails that have 2 T or U nuts per side, that you can slide forward and back. They are made out of aluminum (look like it) and have what look like speed nuts captured in them. My question is what bolts do I need? my experience...
  2. A

    CDL Stuck, won't disengage

    There are quite a few threads on this already, even though the solution may be the same in end I couldn't seem to find anything with my scenario. I have a new to me 1995 FZJ80 with 213k. There is no CDL switch. I only have a CDL and NO diff locks. I was able to test out low range / 4wd over...
  3. A

    polytank fuel pickup size

    I have a poly tank and a 350 SBC, has anybody increased the size of the fuel pickup? 350s are 3/8s and from what I can tell the poly tank is a 1/4. Thanks, arndog
  4. A

    66 defrost hose size

    For whatever reason I thought it was a good idea to remove my defrost hose "adapter" which I made when there was nothing behind my dash. Does anybody know the size of the connection for the defrost connection at the cowl/window for a 1966 fj40? arndog
  5. A

    SBC Grounding

    there are probably a million ways to skin this but talk to me about your grounding, Im using an existing frame hole (threaded) to connect battery and then that to block. turns out it has issues, probably ok when clean arndog
  6. A

    front axle rebuild link

    Looking for a link to front axle rebuild, didn't see it in FAQ and woody's thread/ link is dead closed or missing thanks arndog
  7. A

    Wanted  fj40 bushwacker flares

    Need a set of bushwacker fender flares for an FJ40, I am going to hack them up so dont really care what shape they are in. Thanks, arndog
  8. A

    h4 headlight conversion

    Whats the best headlight to buy? I thought I found a thread a few years back recommending hellas but it was hard to find partnumber Im assuming the hella portion is just for the glass, beam quality, and then the bulb doesn't really matter hoping to get partnumber and plug into amazon and...
  9. A

    thrust washer /lockrite install

    got my rear lockrite installed tonight but the gap is too large .182 vs max acceptable of .170. my thrust washers measure at .070 and .069. Do they make thicker thrust washers? where can I get them? Can you stack thrust washers? this is for the rear of a 40 Thanks, arndog
  10. A

    aquala rod end

    aquala rod end Help Im pretty sure I have an aquala forged double arm but I don't know what rod end I need for the bottom hole (knuckle to knuckle) link, anybody know? is it an fj80 or fj60? the fj40 end I have is to small. rough size of one side of the taper is .625 and other side is .595...
  11. A

    parking light seal

    Anybody know where I can get new seals for the parking light assembly for a 66 fj40 the seal is parth #4 on here http://www.sor.com/sor/cat150.tam?xax=7929&anchor=#150-01A-C thanks arndog
  12. A

    cutting lokar throttle cable

    How do I cut this thing? the firewall end has what looks like a swedged nut on it. I assume this side stays on. the other end has a ferrule(sp?) that Im thinking I remove and cut this side. I cannot get this ferrule thing off and the instructions state ... Don't move ferrule while...
  13. A

    fuel suction line size

    Im rewiring and ripped out the seats to do the fuel sending unit. I was noticing that the fuel suction line is only 1/4 inch. I did poor job of running the fuel hose sometime ago and would like to redo this. I have a poly tank. Right now I have 1/4 -> some fittings -> 5/16 -> fuel pump. It...
  14. A

    fuel guage wiring

    I converted the fuel guage from the stock cluster '66 to work in a 2 1/16 housing. Can someone tell me how to wire it? There are two lugs onthe back of the guage? If neither of the lugs is a ground do I need to ground something? thanks arndog
  15. A

    gm column

    Im working with a gm column out of an S-10. I going to have to get really creative to get it to clear the brake pedal and Im going to have to cut up the dash a little. Anybody have any tricks to getting one of these in an early fj40. arndog
Back
Top Bottom