I'm looking to get a brandnew VNT turbo from Impex-jp. Now when i look at the partnumbers, i should have 17201-17070, but they don't list that, only 17201-17050. After some searching both those numbers appear to be VNT turbos for a 1HDFTE.
Does anyone have the knowledge to know if those turbos...
Just like the title says. Is there some sort of belt driven waterpump that can be fitted to a 1HDFT engine and act like a pump for a water to air intercooler? My truck is 24 volts troughout and i want as few voltage convertors as possible and can't seem to find a 24v electric pump suitable.
Or...
So i just bought a HZJ105 part time tcase (HF1A) to fit on my H151f that came with a full time (HF2A) tcase. Apperently the input shafts have a different spline count. I wasn't aware of that.
Does anybody know if i can swap the input gear so it will fit on the H151f or do i have a very...
Probably wishfull thinking, but does anyone have a non EGR intake pipe taken from a 1HDFT engine, possilbly when installing an intercooler and want to part with it and take the time to ship it to the Netherlands?
Thanks,
Mark
It's the pipe with "turbo" on it
I have this weird high idle on my freshly rebuild 12ht. Even when the throttle cable is disconnected and the high idle actuator is not hooked up to a vacuum source it runs at around 1500 rpm.
I already had this injection pump on my old 12ht (which broke the crank amongst other things....) and...
Hi all,
I've been thinking about replacing the anaeroid diaphragm of my 12HT fuel injection pump while i've got the pump off the engine. It's an almost 30 year old part by now, so it won't hurt replacing it i guess.
Does anyone know a part number for this? Or should i just take it off and go to...
I blew a headgasket on the 12HT and decided while i have the lid of anyway i might as well freshen up the block.
I already have a set of ACL chrome piston rings coming in, but after pulling the pistons i found one set of rodbearings have pretty bad flaking. There is only ~50.000 miles on these...
Does anyone know if there is a vendor somewhere who has a 12HT multi layer steel headgasket on the shelf?
I think i just blew mine (again) and it might be worthwhile to invest in a better one.
I haven't pulled the head or even did a compression check, but the symptoms are exactly the same as...
After a long time debating with myself about the pros and cons. I went ahead and performed a SOA conversion on my 45. And in the process swapped in a Australian import rust free chassis.
I took my time and started to collect parts, mostly found in the Mud classifieds. The partslist i found...
Like the title says. I'm trying to figure out what the ideal mointing point for a tracbar is on a 45.
I'm replacing the frame and i'm going SOA at the same time. I used a Ruffstuff kit on the axle side, so that's fine like it is. Only on the frame i'm just not sure were to weld in an extra...
Hi all,
I'm looking for a set of F250 shock towers for my upcoming SOA project.
The thing is, i can't just go to a Ford dealership in this part of the world and i haven't been able to find an online seller who also ships overseas.
So does anyone have a set collecting dust they want to sell...
Does anyone have any experience in upgrading the power steering pump on a 12HT or 2H for that mather?
I'm getting annoyed with the Toyota pump on it. It's just not powerfull enough for my liking. And i'm on my second pump and it starts to moan again not to long after a rebuilt.
The logical...
I've been thinking about swapping the 12HT cam for a 2H cam to make it a little easier to drive. It's extremely jumpy right now which is annoying in offroad situations. Hand throttle helps, but i want it drivable. I already put an extra spring on the injection pump lever, increased the stroke of...
Just like the title says, the timing gear cover om my 12H-t is cracked.:frown:
It's only two small cracks, but enough to leak and make the engine all greasy. If i wanted that to happen i would have bought a Land Rover.
So the question is, can the cracks be welded and be sure that the welds...
Hi,
This might not be the right place to ask, but here is goes anyway.
I´m in need of some small parts which are considarably cheaper from Cool Cruisers of Texas than any other vendor out here in The Netherlands.
The problem is that from overseas it´s not possible to pay by credit card, but...
Newbie here,
I was wondering if someone one here knows a part number for a LHD 45 series rear wheel e-brake cable.
I know that those exist, but couldn't find a part number and the parts catalog has been no help, because it only lists a RHD cable, which is to short.
I ordered that one...