1978 FJ40 Passenger frame rail two 90* "way" part number 90413-10028. (I think)
can anyone confirm (solid) the size & pitch?
I think it is 10mm x 1.0.
This is the piece I would like to fix/find or replace.
or any resources to get the parts would be appreciated.
1978 FJ40, Original MC (MasterCylinder) rebuilt in 2013 and again now.
Removed and cleaned the PV (ProportioningValve) by removing and inspecting the 21mm nut, spring, rubber washer, and confirmed fluid flow. (Seems good??)
Bare with me as I attempt to explain:
Was driving and discovered the...
Did the engine rebuild and have been driving occasionally. Short mileage. Of course used high zinc products and have already done one oils change at about 100/150 miles. Continuing with high zinc products.
My question is: what if any are my limitations for longer drives. Do I need to keep...
Very simple.... Opinion question.
I have shopped for new rotors on my 40. O'reilly's has a 38.00 for the best brake rotor. Advanced has two 50.99 or 125.00 for the Beck Arnley. From Toyota 112.00 for theirs. I am not too concerned with the price point. Just wondering why such differences...
I have a misc wire I have no idea where it goes to.. pic 1 & 2 & 3
any ideas?
Situation #2
I just bought two OEM license plate lights.
I have some ideas, but want to confirm before I continue.
The lights have both a green on each and a white W/black on each.
My harness has two...
What's your opinion? The more responses I get will help me decide what to do...:
Found a company that will laser print and restore face plates inside the gauge clusters. The initial set-up cost is pretty outrageous, artist, layout, etc.
That said, as a way to give back to fellow Mudders I...
As hoping someone would take a measurement for me....
I need the distance from outside the cowl drivers side to center of the hole on the rear of fender.
My aftermarket fender is a bit "off" (twisted) this proper measurement off of a stocker.....
Thanks, in advance
Two things here ...
First is pretty easy....
What is it (yes a sensor) but for what? And there seems to be a few places it will mount..... Where is correct?
This is the piece in question?
Second.... I mounted and plugged up fender sidelights.
My turn signals are not working?? All lights...
Ok, I am at my wits end here with this thing.
My other car is a 96 EB Full Size Bronco. 220,000 miles and in great condition.
Over the past three years, ever since dealership replaced the sending unit, my gas gauge is possessed. It seems to work normally from full down to half a tank. THEN...
Need a 1978 entire guage cluster. Doesn't have to be perfect. Blemished is just fine...
If you got an old one laying around with a messed up gauge or two that is also fine. Just need a cluster that will fit my stock set-up 5/78
Thanks
Would like to buy gauge cluster; ashtray; glove box door for 5/78 FJ40. Condition is very flexible.... Need all 3, blemished ok.... Anybody got these as surplus? Thanks
OFF got two wires I can't seem to identify. Done pretty well with everything else. Thanks to y'all.
Wire on left is riding in main rear harness. Just hanging out there.
The wire on the right is coming of the "finger" or "splice" leading up to reverse light connection, seatbelt, fuel sender...
Anybody have a remedy for graying roll bar pads. Can or has anyone tried to dye or paint them? Looking for a remedy without having to buy new ones..... I was hoping maybe drop them in some RIT dye and hoping not to ruin the padding... Any personal experience to refurbish?? Thanks
Getting ready to put 4* castor shims on the front. Everything I read says to put the thick part of the shim to the front. That I find...
My logic says to put the thick part it in the rear. Which would roll the tire counter clockwise fixing the castor. Am I just not "getting it".
Any...
Hey Grant thanks for the headsup....
Change of subject... only working off Haynes manual and Mud. Apperently FSM is a better way to go. Are they still available in the entirety or does anyone know where I can aquire one?
As you all know I am very new at the wrenching side. I am now very concerned about this project and need some true advice here. After hearing all the struggles with getting old bushings out. I did not experience any of that. Was very easy. (alarm/alert)
I have some real concerns about...