Search results for query: *

Forum search Google search

  1. OzarkMtnCruiser

    Found a wire that needs to be reconnected..

    I believe the round connector goes to ground? I think I left it off when i did the headlight upgrade. The wire goes to the that connector and then to the module that's connected by the coil.. what is this circuit? As always, appreciate it guys!!
  2. OzarkMtnCruiser

    Won’t start..

    Fire from the coil, fire from the end of the of the plug wire, fire at the plug- pulled the gas line to the carb and gas is coming out- site glass is half full. Changed the fuel filter, plug wires and plugs, rotor and cap and put a new fuel pump on her about a year ago. Ran this truck 200 miles...
  3. OzarkMtnCruiser

    For Sale  Emission Control fj40/60 ‘80-‘87

    $75 TYD
  4. OzarkMtnCruiser

    Radiator assistance-

    Is the top square nut on a stud or am I going to have to loosen the condenser to get to the back of the bolt? Thanks-
  5. OzarkMtnCruiser

    fj60 radiator

    Thought I would pass this information along in case someone is in need of what appears to be quality aftermarket rad- I saw in post where a fellow mudder had ordered a CSF rad from Performance Radiator- googled them, found their site and started looking around. Found one that was built for 81-87...
  6. OzarkMtnCruiser

    Great price on Denso Plugs

    https://eeuroparts.com/product/denso/3013 Shipped for $18.40
  7. OzarkMtnCruiser

    What kind of tip ..

    do you use to grease the anti friction pads on OME leaf springs? thx
  8. OzarkMtnCruiser

    Mud flaps rusting out.

    Any ideas on mitigating the rust on these flaps?? Thinking about removing that rubber, spray it down good with primer, then take some jb kwickweld and put a layer down then apply that spray rubber flex seal over it- Think that will work? Or should I use that or another type of epoxy? Also, does...
  9. OzarkMtnCruiser

    No voltage at the dome light-

    Blower fan works, rear cargo light works, fuse is good(tested with vom), sanded the door contact and still nothing- The other day when I took the cover off the clip and pin on the left side of the bulb fell out?? The pin didn’t look like it was not connected to anything, so I glued back in.. The...
  10. OzarkMtnCruiser

    Will this bull bar bolt up to a 60 bumper ?

    Thanks-
  11. OzarkMtnCruiser

    Wanted  OMESB1 bushings

    Anyone have any new OMESB1 bushings laying around they'd want to get rid of?? I need 7, rather not pay for a another set of 6 just for one bushing... Thanks
  12. OzarkMtnCruiser

    Broken bolts in hub

    Nice surprise taking the bolts out of my hub cover- two broken bolts that had been “glued” back in.. ideas or tricks on getting the rest of the bolts out of the hub body?
  13. OzarkMtnCruiser

    So, who's going to have the first Tesla powered cruiser?

    https://www.motortrend.com/news/tesla-crate-motor-ev-conversion-small-block-v-8/?sm_id=organic_fb_MT_trueanthem&utm_campaign=&utm_medium=&utm_source=&fbclid=IwAR2gcCwcyRYdEE4cBxrI3x7w0yusrtg6aJ27gXyXpF8oyxnFzRemyNDq2es
  14. OzarkMtnCruiser

    60 won't start without...

    I've always had to pump the pedal more than i should to get her to start- but now my 60 will not start without starting fluid. After a shot she starts right up and runs, the idle speed is a little low but she stays running without the choke. I can turn her off and she'll start back up but if I...
  15. OzarkMtnCruiser

    Drive belt question-

    Anyone know the Napa / AZone part number for the belt you can use to run between the alternator and crank, eliminating the power steering pump? Thank you, thank you very much..
  16. OzarkMtnCruiser

    Datum line measurement of a stock fj60 leaf spring

    Does anyone know the measurement of a stock uncompressed leaf spring from the center holes of the bushings? Just bought a used one and I'd like to see exactly how flat it is.. thanks edit: it's the rear spring
  17. OzarkMtnCruiser

    Pulley on the power steering pump is wobbling

    Any idea what would cause this? Just saw it today.. thanks http://s47.photobucket.com/user/dwdva1/media/ih8mud/20140105_193558_zps1c745b5e.mp4.html
  18. OzarkMtnCruiser

    Don't F with a cruiser..

    http://www.liveleak.com/view?i=52b_1358175754 Gotta do better than that!
  19. OzarkMtnCruiser

    not sure why this topic was closed by the mods.

    but the invitation still stands- anyone think they can crawl through this dry creek bed is welcome to try.. https://forum.ih8mud.com/tn-bluff-city-cruisers/523484-any-you-guys-think-you-could-crawl-through.html
  20. OzarkMtnCruiser

    need RT assistance on a 4 speed tranny

    I have a 60 4 speed and I'm stuck in reverse. I've pulled the gear shift lever out and here is what it looks like- to quote another mudder he said: Take the shift lever out and look inside the top cover (with a flashlight) at the shift rod slots. There are 3 of them and all 3 slots have to...
Back
Top Bottom