Search results for query: *

Forum search Google search

  1. franzugan

    1hd-t with td05 mamba not boosting

    Tried that as well, wired it with binding wire and no change although there is no way of knowing if it opens a couple of mm even with the wire
  2. franzugan

    1hd-t with td05 mamba not boosting

    Yes fitted the stiffest spring and wastegate starts opening at around 22 psi
  3. franzugan

    1hd-t with td05 mamba not boosting

    There's been a few people running these turbos around it's been working fine for them. Here's the link to the turbo. https://www.shop.mambatek.com/12-6-Billet-Turbo-TOYOTA-Cruiser-1HD-T-1HD-FT-3-TD05H-16G-7cm-001-1076.htm
  4. franzugan

    1hd-t with td05 mamba not boosting

    Both turbines have 12 blades
  5. franzugan

    1hd-t with td05 mamba not boosting

    Checking how freely the blades spun. Checking if wastegate gate sealed properly
  6. franzugan

    1hd-t with td05 mamba not boosting

    Forgot to add that I'm running a top mount, 3" straight through exhaust and changed oil and all filters 500km ago
  7. franzugan

    1hd-t with td05 mamba not boosting

    Hi everyone, Long story short, the Ct20b I had on my 1hd-t started leaking a fair bit of oil and decided to upgrade to a td05 16g 7cm and 12 + 12 blades mamba. The car was going quite nicely and had a good response down low (unfortunately I don't have any numbers to compare it with) Bolted it...
  8. franzugan

    Yes I know another turbo question

    This one
  9. franzugan

    Yes I know another turbo question

    Yes. I bought boost and EGT gauge just for that as I would not attempt any tuning without those 2 and then IC air temperature in and out just for curiosity.
  10. franzugan

    Yes I know another turbo question

    Thanks for the reply.... I'm running a Ct20b from an fte. I bought an uprated turbo kit with the 360 deg thrust washer and was told that with that I can increase the boost to 18-20 psi.
  11. franzugan

    Yes I know another turbo question

    Hi guys, yes as the thread's title says another turbo question... Attached is what I'm currently running but I would like to upgrade. I have been reading lots about turbos and mods and compressor wheel size and turbine size but I still don't get hf of it. The question is, are there any bits...
  12. franzugan

    The official 1HDT Intercooler thread

    All setup and ready for testing!
  13. franzugan

    The official 1HDT Intercooler thread

    Upgrading my old Isuzu intercooler with a new 450x300
  14. franzugan

    Alternator part number

    It's on my 1hd-t. Wanted to know if I should swap it for the 100A unit above.
  15. franzugan

    Alternator part number

    Awesome thanks! Would you know what this one is then? Sticker is broken and the Internet is not helping
  16. franzugan

    Alternator part number

    Don't know why it rotated the picture...
  17. franzugan

    Alternator part number

    Hi guys, was just wondering if anyone could identify the part number on this alternator. It's on a 1hd-ft but looks bigger than the one I've got. Cheers
  18. franzugan

    Covering part time to full time 4wd

    Thank for all the info guys! Full time transfer is being transplanted as I'm writing this!
  19. franzugan

    Covering part time to full time 4wd

    I meant part time! Thanks for pointing that out and have edited! Don't have ABS so not sure why transfer will not work without it.
  20. franzugan

    Covering part time to full time 4wd

    As the thread says, I've got a part time 80 series. Transfer is buggered and cannot find a part time transfer here in the country. Only full time 4wd available. Is it only a matter of removing the part time transfer, bolting in the full time transfer, connect the wires and the car is ready to...
Back
Top Bottom