I'm moving and these need to be gone by tomorrow 10/31!
Free to anyone who can pick them up in Westminster, CO.
https://post.craigslist.org/manage/4113559138
I will not ship. I have no time to carry these around but I'd rather see them used than toss them.
I decided to buy the last hose made for the ABV assembly. The hose that runs from the ABV to the air injection rail. Went to replace it today and found that the check valve on the air rail has completely disintegrated. Rust particles had fallen down into the bottom of the ABV and started to...
Every morning I follow the same starting routine. Couple pumps of gas, full choke and she fires right up. After a bit I close the choke and idle is right where it should be at 650. After driving for any length of time the idle will not go back down to 650. It sits at 1000 or a little under...
Today I attempted to remove a bypass of the rear heater line that runs behind the engine. The PO had installed a flush tee that was leaking and had to go.
Since most of the hoses needed to properly fix the system are NLA I just decided to remove the rear heater completely.
My question is...
No longer need these since I got rid of my backing plate. These are from Man-A-Fre.
$30 for the pair. Local pick up or add $5 for USPS shipping. Paypal preferred.
I'm having some stainless brake lines made up since I eliminated my backing plate.
Anyone know what size and pitch I need for the inlet into the caliper? I think it may be 10mm 1.00 but want to be sure.
Just got back from a weekend of fishing and camping at Chinn's Lake near Saint Mary's Glacier. After spending the majority of last month rebuilding my front end and brakes front and rear it was time to enjoy the rig. The road up isn't especially hard. Some steep rocky sections and that's about...
I'm picking up a set of 4.10 thirds from an 84 FJ40. I was wondering if there are any issues with the swap.
Any differences in splines, flanges or that sort of thing? I'll need to compose a laundry list of stuff to replace while I'm down there.
I have the classic wheel well rust where the rear seat brackets attach.
Should I remove the outer plate that seems to be the cause? I have my rear seats removed but I'd like to keep the brackets in case I ever sell...which I doubt.
I decided to take out my rear seats. After a couple camping trips it became apparent that I'd be better off taking them out and gaining a lot more cargo space.
This is what my sleeper panel used to look like. One end rests on a lip on the back of my cargo box. The support piece rested on the...
ANyone have experience with these? Or perhaps pictures of one installed? Seems to be one of the only 9.5" covers out there.
Land Cruiser 9.5" Differential Cover - RuffStuff Specialties
Well after spending what seems like every weekend working on my 60 since it came home I finally got to run some trails.
Headed up to Idaho Springs and ran Barbour Forks on a clean up run with Front Range 4X4. Also did Devils Canyon which ended up being a snowy adventure. Was pretty impressed...
Spent the weekend assisting with the build of my new bumper. I sourced the photo archives of the 60's forum for my favorite bumpers. Ended up reusing the vertical supports off my old Specter bull bar.
Personally, it doesn't feel right to tell a fabricator "build this" and pick it up when it's...
After the new suspension install my axle breather kept popping off. So today I put on some longer hose. While trying to figure out where to put the end I spied the bolts I had put in when I removed my rear seatbelts. So I took out a bolt, routed the hose through and put the breather cap back on...
I just picked up a nice set of 4 Runner seats from an 89 SR5. I known some forumites have swapped these into an FJ60. Just curious how you adapted the 4 Runner seats to work in a 60.
I have a set of Doetsch Tech Prerunner shocks for sale. They are 26.5" extended to 18" compressed eye to eye. Doetsch Tech sent me shocks longer than I needed. They have never been used but are a bit dirty from me test fitting them and discovering they were too long. I'll clean them up a bit...
With new legs my FJ-60 also gets a new name. Now she/he is now Bjorn. ReBjorn and Bjorn free. :flipoff2:
Woke up this morning to grey skies but no rain. Rover67 came over around 8:30 and we got started. My other helpers bailed. Still have a fridge full of burgers, brats and beer they missed...
Next weekend I'll be installing my new suspension. :clap: I have a guy interested in my stock springs to use on his 4 Runner. They are 27 years old and totally flat, not that that matters as much for his application.
Just curious what they would be worth in trade. Are they worth a set of...
I got this demo FJ Cruiser MPAC side rack from Doc at Springtail Solutions. The size is 19" wide by 11" tall. I figured it would fit nicely on my rear cargo panels. I'm always looking for ways to keep stuff organized, out of the way and easily accessible. I can't stand digging for stuff or...