Search results for query: *

Forum search Google search

  1. bushwhacker07

    RTH 1000 miles from home in colorado

    Hey guys I'm in grant colorado 1000 miles from home just replaced front wheel beerings now I have ujoint going out. I hav shaft out and getting ujoint in morning was wondering if anyone has a vise I can use or any suggestions how to change without vise. Any help would be greatly appreciated. Thanks
  2. bushwhacker07

    RTH front end noise 1000 miles from home

    Ok so replace front wheel berring still had noise finally ran it down to the rear u joint the only prob now is I needa vise and a couple ball peens is ther anyone in the grant colorado area that could be of some help I can get a ride a little ways. Any help would b great.thanks
  3. bushwhacker07

    RTH front end noise 1000 miles from home

    I greased birfs b4 leaving they are nice and lube, since post I hav been takin it apart but have ran out of light. Its lookin like wheel bearing will find out in the morning for sure I'm currently located near grant colorado, where is best place to get parts round here especially on sundays back...
  4. bushwhacker07

    RTH front end noise 1000 miles from home

    I am 1000 miles from home and currently in Colorado. front pass side wheel starting make faint chirrping noise and now way worse it only does it under load. I have a 92 wit center diff lock button. Would it work to take front drive shaft out and lock diff in high range and drive home or do I...
  5. bushwhacker07

    Sky high 80's

    In my first reply I said it was not an 80 I said it was just tall thats why I asked before I posted, Wasnt trying to give attitude the guy seemed interested with quick post figured I would give him video instead of pic, and I will take a pic with my 80 in with it tommorow when I get to shop.
  6. bushwhacker07

    Sky high 80's

    Here since you seemed so interested you can watch it in action, bogger49 - YouTube Not trying to hijack thats all i got to say bout that
  7. bushwhacker07

    Sky high 80's

    Figured asked before I posted but I have a rig that is really tall and just so you know its not lame I know for a fact NONE of you have seen one ever before its on 60" rice and cane tires for a lil teaser
  8. bushwhacker07

    FJ Cruiser Wheel Questions, Answered

    I will be taking my tires off old rims manually tommorow we have a scale at our shop I will weigh my factory 92 fj80 15x7 aluminum rim and get back, I wish I could have got weight of fj wheel but I had someone else mount and balance. The shipping weight on the 315 goodyear mtr was 66lb
  9. bushwhacker07

    FJ Cruiser Wheel Questions, Answered

    fj wheels and mtr's Figured this was best place to showcase new fj alum. 17's, and 315 mtr's as you can see they have already dominated a red bull can in the driveway:grinpimp:. I have no spacer, as I read the only way to get center caps to fit on front is a spacer. Has anyone modified the...
  10. bushwhacker07

    Post up some pics of you hood blackouts!

    We make vinyl stickers the rolls are 3ft wide, as that is as tall or wide it could be all we need is your measurements.
  11. bushwhacker07

    RTH: Weird cooling system behavior

    I think you answered it "if it was circulating, it should have warmish hoses wouldnt you think"? If your hoses never get hot then your not flowing any liquid through there. After a cold start how long does it take before you get heat out of your vents?
  12. bushwhacker07

    RTH: Weird cooling system behavior

    Yes they should look the same when I got mine you could get 170 degrees or 190 degrees. at 170 or 190 is when it would open to allow full flow of your coolent through your block. If your running somewhere real cold your 170 might take along time to ever build up heat or pressure.
  13. bushwhacker07

    RTH: Weird cooling system behavior

    sounds like thermostat, what size did you put in when you installed new one? or vapor lock
  14. bushwhacker07

    Rth stuck in Nashville with a broke down 80

    I noticed everything to do with spark was new but the coil. If you had a good coil around I would try that as sometimes when they are going bad they still fire or spark just not enough. They can do funny things as there is oil inside that breaks down over time, If the fuel isnt burning right...
  15. bushwhacker07

    What size spring spacer do I need?

    Park on level ground measure from ground to the bottom of your fender flare in the center of it like inline with your axel shaft, do this on the back first. then measure same spot on front fender flare. Subract difference and thats how much you need to be level.
  16. bushwhacker07

    Rth stuck in Nashville with a broke down 80

    How much gas is in the tank when it starts acting up? Does it do this when it is half full or less, or does it do it even with a full tank? It could be something in your gas hows your fuel quality? If you have done all the electrical testing as you said and havent found the problem make sure...
  17. bushwhacker07

    Custom Bumpit-Offroad bumper

    Yes we do all our own fab from raw steel. We are currently working on making a 4 link front and rear from scratch. I do understand something that might seem easy to one guy might not be as easy for the next. some Just what to buy and bolt on wit no headaches others wanna build.
  18. bushwhacker07

    Custom Bumpit-Offroad bumper

    Well I wasnt bashing at all. Or trying to take anything away from your bumper it does look good. sorry if I came off wrong. And as far as telling you that you paid to much, I was just showing what you could have got on on a comparable budget. HOnestly I dont care what you pay for your bumper its...
  19. bushwhacker07

    Custom Bumpit-Offroad bumper

    "Thick steel" I wouldnt use that term until you get into 1/2" as you can buy affordable welders for around 500/700 torch around 500/700 that leaves 1000 for steel and supples. I would think your bumper is not over 3/8's wouldnt suprise me if is 3/16 to a 1/4 and you can get strength from bracing...
  20. bushwhacker07

    Custom Bumpit-Offroad bumper

    Holy cold steel batman :eek: Couldnt you buy a welder, torch and all the supplies and steel to DIY for that? Then you would have welder/torch for next job. However if you dont have the know how to do something like this then I guess the price would be about right. Sounds like I needa get in the...
Back
Top Bottom