I have been looking for some fog lamp options for my FJ60 ARB bumper and the 2 options I could find were the Slee inserts and the ones direct from ARB for other series bumpers. I did some searching and couldn't find anyone that had installed any of those options (or fabricated ones) for these...
I am doing a SAS on my 2003 Tacoma DCSB and have the front and rear suspension and some other misc parts for sale. Truck had 163,000 miles when parts removed.
$800 for all of it.
Front IFS assembly - complete hub to hub w/ calipers - cut off frame in 1 piece.
upper A arms
1.5" front wheel...
For Sale: 1975 FJ40 VIN:FJ40193478 - Matching Tub and Frame
I bought this FJ40 from a guy in New Orleans in 2013 and it had been painted tan and had a SOA done to it when I purchased it. The SOA was not done to my liking, so it was redone using a Ruff Stuff SOA kit using FJ62 axles. The TBI...
I have a used working orbital steering valve. I was going to use it on my kids rock crawler project, but it is too large (too high cu-in/rev) for my application. It is a Von Ruden Orbital Valve. "Open Center" non-load reacting steering valve 9.6 cu-in/rev or 160cc/rev displacement ratio. PM me...
I have a set of FJ62 thirds with 4.11 gears and open differentials for sale. They have been in my garage for a year or so now and I went a different direction on my 60 and no longer need them. Gears look good and bearings feel tight. $450 + shipping or pick up in Longview, TX. We travel to...
A few months back I purchased an ARB air locker for the rear of my 60. I finally got around to installing it this past weekend and all went good until it came time to install the trust block and measure the gap to determine the c clip thickness - (ARB sends 4 different width c clips). I started...
So I was searching for landcruiser parts one day and ran across a kids rock crawler jeep that a guy out in CA build for his 4-5 year old son. Didn't pay it much attention at first, then I got to reading into it and thought this would be a really cool one of a kind project for my son. He is...
I know its a Toyota forum guys, but I'm looking for a Samurai transfer case for a project I'm gathering parts for. It needs to be a divorced transfer case with the ability to have low gears installed in it for a reasonable price. PM me if you have one or have any leads. In case you're wondering...
I have an M101A2 military trailer for sale. Registered and tags good until June 2018. I just re-wired the tail lights with LED lights and and flat 4 connector. I removed the old military lights and wiring. I do have all the original wiring and lights minus the original military round connector...
Installed my Trail Tailor rear bumper today abs I have a factory rear bumper and a factory front bumper with tabs for my 8" hella lights to get he off the grille for sale. I also have a draw tite 2" receiver hitch that was blasted and painted a few years back. I have the factory 60 rear tow bar...
Installed my Trail Tailor rear bumper today abs I have a factory rear bumper and a factory front bumper with tabs for my 8" hella lights to get he off the grille for sale. I also have a draw tite 2" receiver hitch that was blasted and painted a few years back. I have the factory 60 rear tow bar...
I am in the middle of my LS swap and I purchased an adapter from Markd 4wd to use the factory 2F temp sender. The new one I bought from the parts store is about 1/2" too long and bottoms out in the adapter. I talked to another guy on the forum that used the factory one from his 2F and it worked...
I was running the wires to the driver side headlight/horn/marker light inside the fender to clean up the look for my LS swap. This plug was in the wire loom and I cannot figure out what it could have gone to. It has large gauge wire and I can't help but think it may have been for a second...
I have a diamond plate Aquila storage tailgate that was on my FJ40. I went back with barn doors and no longer have a use for it. It is in good shap and all the hinges and latches are there. $300 plus shipping.
I have the original transmission and transfer case that came out of my FJ40. Worked as it should have when pulled. I used the output flanges and 4wd selector assembly. I have a shifter and a new 4speed knob to go with it. $250
I have a set of front seats and brackets that came out of my 75 FJ40. They are in good shape. See photos. $300 plush shipping if not picked up in person.