My Temp gauge quit on me today. All the others work fine. I am guessing it's the sending unit, but I don't know were on the engine that part is. I have a Haynes Manual and for the life of me I cannot find it in the book either!
If it were the fuse the other gauges would be dead too, they...
Just read that pile of data in the tire sizes with the the lift used. That was a ton of info from across the country ( and out of the country too)
While reading this I wandered how many guys swap R&P as well to keep the torque needed off road? And at what point did you notice that the tires...
I'm not a rock crawler, but I do have a desire for additional traction in the front. I have an aussie in the rear axle. I also have manual steering which may be swapped in the next 10 months to a year. My cruiser already does about everything I would like it to do for my needs, Just hate seeing...
Okay, I have this dilemma which I'm sure must have been posted about in the past. I have a few bucks into my Cruiser which makes it worth a whole pile of money more then Blue book.
I have liability insurance to be legal to drive on the road, however I cannot figure out how I would insure this...
So what do you think? I had a 76 CJ5 with a detroit locker in the rear. An awesome traction adding device, but left me freaked out a few times at highway speed with random locking.
I had a 93 toyota pickup with a Tru trac front and rear. It was only okay at best off road. Still spun a tire...
When it's freezing cold I pull the choke, pump the gas twice and turn the key, it cranks a couple times and fires right up.
When it's hot after running it, I just leave the choke in, turn the key and it fires right up.
When its been hot from running and sits of 30-60 min, that thing...
This carrier is about everything I want it to be. However to open and close the rear doors is bugging me lately. The latch and pin system is a PITA.
Anyone convert this to a more practical system?
Does it really matter which end is which? I've noticed this on different makes and models and seen the spline end on the axle side or on the transfer case side? Does it really matter or is it make and model Specific?
The mirror vibrates quite a bit blurring out, especially noticeable at night with the car behind mine's headlights. All I need to do it lightly touch it with my finger tip and it's rock steady. Is there a tightening adjustment on these? It's a stock original 1977 mirror.
Yeah, I was anxious and excited to get this all back together, it's fully functional now and needs nothing else. Although I do need work on the dash lights and there is no radio yet.
I worked with a buddy to fabricate the winch mount, bull bar, and rock rails. He is a metal fabricator for a...
What is the best off road light set for about 500 bucks. I will wire direct with 10 gage wire, and a relay. So the control and power is not an issue. Just the absolute baddest brightest off road light you can get for about 500 bucks or so.
PIAA makes an Extreme white, there are also HID...
I just bought this winch for my cruiser, I have to fabricate a mounting plate but it seems it may need to be off center a bit to get it to sit between the frame. Anyone with pictures of this winch, please post up.
I have the bull bar and winch mount built and test fit. However with it mounted to the frame my body seems higher on the left the the right side. It's actually about an inch or so off. Not at all noticeable without the bull bar that goes up over the lights, but with it on the frame the bezel is...
My 77 has the pipe right below the center skid plate. I have the Stock 2F and I need to route and securely mount the pipe out of the way. It certainly cannot remain the lowest point.
So have you all mounted it above the skid plate or in another area? Looking for some ideas so I can do this...
If ever there was a tire made for the cruiser! My first jeep and cruiser back in the early 70's both had these tires. Every once in a while You see a Cruiser with the Trutracs or the larger version the Rhino's.
!
Sure miss those true tracks what a great tire for the cruiser
I have the factory original floor mat, Its beat and the rest of the rig is all refurbished. Is there anything that is really great besides the original, any aftermarket heavy duty ideas?