Search results for query: *

Forum search Google search

  1. M

    craigslist  1981 FJ60 $2500, Oregon

    Pictures can be seen on the craigslist ad. http://portland.craigslist.org/clc/cto/3920198979.html 1981 toyota landcruiser. 383 SBC motor swap, 4 speed, Spring over axle lift for around 8" of lift. 63" chevy springs in the rear. Marlin Hi-steer cut and turned front axle with a complete...
  2. M

    Pinion depth shim placement question

    I'm working on installing my new 4.88 Nitro gears with master install kit. After reading through several of zuk's installs it seems that pinion depth is adjusted by adjusting the shims between the pinion and inner pinion bearing. However the master install kit I have, has shims that are way to...
  3. M

    For Sale  81 fj60 383 sbc soa- $4000

    81 fj60 383 sbc soa- $3500 81 FJ60 383 SBC rebuilt less than 7500 miles ago edelbrock carb with offroad spring loaded needle valves, also includes a used holley projection FI setup. Spring over axle, 63" chevy springs in rear, cut and turned front axle rebuilt knuckles with marlin seals and all...
  4. M

    For Sale  1981 fj60 383 SBC, SOA $4000

    Abort mission, can't figure out how to delete thread sorry Dan
  5. M

    1976 fj40 rear axle

    ****SOLD****1976 fj40 rear axle minus third member. Located in Portland, oregon area $100 OBO. Local pickup only Thanks Dan (503) 935-0856
  6. M

    craigslist  81 fj60 383 SBC SOA

    The build $3750 Have to be trailered or repair the pinion and drive it. Located in Molalla, OR. Any serious interest call Dan (503) 935 0856
  7. M

    Wanted  4.11 fine spline third member

    Looking for a 4.11 third member to go into a 81 fj60. Ideally from an fj62. Fj40 with fine splines or rear from an 80 would work aswell. Thanks Dan
  8. M

    Broken pinion shaft

    Went out wheeling yesterday and snapped my rear pinion shaft in half at the front splines. I was articulating a bit with the rear (approx 1') and going up a steep short climb to a bypass started to spin, backed about 2 feet took another run at it and then POP. Fairly certain I was just to heavy...
  9. M

    Test run

    a few pics from the test run. Trip was quite a few logging roads, some gravel pit fun, a couple rutted out hill climbs and the last mile or so was a boulder trail. I really need to get my fuel injection installed as it would die every time I got on any real steep inclines but the suspension did...
  10. M

    Front Driveline length

    After the lift I'm going to have to extend my front driveline a bit, Anyone ever try just making a 1.5-2" block between the driveline and the front differential? Any other cheap and relatively easy options? Thanks
  11. M

    SOA: The begining

    Well I traded a 71 scamp for a 1981 fj60 with 4" SUA lift springs and a 383 chevy stroker motor last month. I drove it on a couple of wheeling trips and while it has tons of power can't get any of it to the ground with my worn 32" bfg a/t and stiff suspension. Probably would have been an OK...
  12. M

    fj60 third member swamp

    Morning. Trying to get a little better gear ratio for my SOA happening over the next couple weeks already converted to a 383 stroker motor so I think 4.11 should be good to run 35"-36" tires once I'm done. I found a 71 fj40 front axle with 4.11 gears for $50 and have another third for next to...
Back
Top Bottom