I am looking up part numbers for an OEM brake master cylinder for my 1994. There are two that come up. There is a 47201-60550 FZJ80 W(*66) and a 47201-60540 FZJ80.
What does W(*66) mean?
I had a little weird thing happen. I just changed the oil on the 80. Using the same Castrol GTX SAE 10W-30. Went from my last OEM big filter to the OEM small YZZD3 filter.
Now when I start up, the oil goes to the third tick mark of four tick marks (bottom, two marking thirds and the fourth the...
I'm looking for a recommended shop for an alignment. When replacing the tires I noticed that my camber is off a bit on the 86 4Runner, time for an alignment.
I think I'll take this opportunity to mildly crank my torsion bars to remove a little of my stinkbug. I've never done this, but it...
This is long and I apologize.
TLDR: Can people with a known 17 gallon tank or a known 14 gallon tank measure the depth of the fuel tank at the midpoint of the tank about where the fuel pump hanger/fuel inlet hose is? Fuel pump hanger depth from a known tank would work too I guess. Thanks
For...
Hello Mud electrical geniuses,
I'm building an auxiliary underhood fuse/relay box from a Toyota OEM fuse/relay box I've gotten at the junkyard . My question is I will be wiring 2 20A micro relays to be engine running only. My initial plan is to go off the alternator fuse (this may change). I...
Sooooo, I have always been trying to figure out things most of you guys probably learned in the womb. I’ve never been able to check the torque of the knuckle nuts that are next to the dust shield. I’ve just put a wrench on them and gave it the Ol’ German gutentite. I’ve never felt that very...
During my recent front axle service I discovered what I thought was a leaking power steering pumping marking the pavement was actually this little doohinkus in the upper oil pan.
That monster hex bolt/plug is part number 90341-27006 and gasket part number is 90430-27005 according to...
I’m doing front axle seals and while cleaning the passenger side it looks like whoever was in there last was a little rough on things. The damage is on the machined surfaces.
I’m trying to decide if it is not an issue and run them as-is. Should I just debur with a file an run it? Last option i...
I developed a cold no-start last week when I tried to drive home after work. I went to start and acted like a dead battery, no gauge, fan, clock, radio and buzzer. However, the dome light was dim and the rear window worked normally with the key. I'm at work and all I had was my free HF DMM...
I hope that this is the right club to post in, let me know if either of the other clubs is more appropriate.
Well, out of the blue my wife has been head hunted for a job in Richmond. It has now reached the point where she is flying in for an interview in the next week or two. She is going to...
These electrical plugs always give me grief. For the life of me I can’t unplug this door switch connector. Anyone have some advice for this moron?
I’ve tried all my usual tricks with picks and tiny screwdrivers.
I've been contemplating swapping in manual seats for years. My head rubs on the roof a little. My passenger side forward-back motor is dead too. Besides, I just hate electric seats.
I have been looking for 6 months for a set of seats from a 1993-1995. There have been none local, just one seat...
Pulling into Prescott Valley I noticed my engine temp start to rise in my 1986 4Runner with a 22re. Shut off the AC and they went down to almost normal. AC temp switch didn't trigger so I am probably alright.
When I stopped I went to spin the fan clutch and the fan is free wheeling. I don't...
This is a real time work in progress and I've been working offline with @flintknapper and @1972FJ55 on how to do this. If seen this mentioned, but no detailed "how to".
Background, my compressor would make the occasional grinding noise on start up, but worked fine. I just assumed it was the...
I'm putting my interior together and the thickness of insulation prevents the little snap locks from engaging.
The stud welded to the floor is an M5, but I'm having trouble with the pitch. It isn't .5 or .7.
Does anyone happen to know the size of this stud? Thanks
I forgot to ask this question. When I removed my carpets I found these metal clips. I'm thinking they for the plastic carpet sills but have not figured out how they attach.
Anybody recognize them?
I did a long laundry list of maintenance on my 1994 Land Cruiser only to end up with a misfire. I also have a new CEL, #25, that is probably related. I was pretty bummed.
I left it with my mechanic for him to use his fancy oscilloscope to test the ignition while the family and I went to play in...
I am taking another hooky day and cleaning the ports on my upper intake manifold. There is a little two pronged fitting that is sealed into the manifold that connects some vacuum lines. I see no reference in the FSM, a parts diagram calls it the gas filter #1, part number 90917-11023.
Anyone...
I'm about to pull my injectors to have them cleaned. I know that the o-rings needs to be replaced as well as the fuel inlet gaskets, injector grommets and injector vibration insulators per the FSM. Do I need anything else?
Well, reassembly of the 80 is delayed again. I thought I might r/r the fan clutch. Kevin helped me the first time years ago. Does anyone know a local (Tucson) source of the silicon oil?