Search results for query: *

  • Users: Anvil
  • Content: Threads
  • Order by date

Forum search Google search

  1. Anvil

    EFI 15 amp fuse blowing

    I've researched a lot and watched many Youtube videos... I'm still at a loss and need some advice. Thank you in advance! The EFI 15 amp fuse keeps blowing on my girlfriends 1995 80. The Cruiser will travel 10 to 12 miles when cold, then the fuse blows. It then blows a fuse every .5 to 1 mile...
  2. Anvil

    Left rear turn signal voltage problem

    My left rear turn signal quit working. After installing a new turn signal bulb, new harness, and new flasher relay... I have fluctuating voltage at the socket. I get 12 volts, then the voltage drops to 3 t0 5 volts for a few cycles, then 12 volts again for a cycle or two. This happens when the...
  3. Anvil

    Fridge question

    I'm going to install a 58 quart fridge with a sliding rack on my drawer system in my 1997 80 this week. What is the preferred side to mount, driver or passenger? The lid will open from eaither side, so that's not an issue. I go back and forth, and can't decide. I see good reasons for both, and...
  4. Anvil

    1FZ-FE head rebuild price

    I admit, I'm ignorant on the cost of machine work on a 1997 1FZ-Fe head! Just want to see what you guys think. I little history... I provided new OEM valve seals. No new valves or springs were needed. The head surfacing was .0030. Originally, I was told $800ish... Final bill is $1192. Is that...
  5. Anvil

    Brake related grinding noise

    I been searching for the last two hours ... learned a few new things, but haven't found what I'm looking for. Last summer I did a brake overhaul on my 97 80. I replaced the master cylinder, calipers, rotors, brake lines, with OEM parts. The new brake pads were EBC green. I also replaced all...
  6. Anvil

    Death wobble question

    I had a death wobble on my 1997 80 . I replaced bushings, wheel bearings, tie rod ends, balanced tires, blah,blah, blah. I finally replaced the tires with Cooper stt pro 37x12.50r17's. The death wobble was gone. Everything worked great! After 5,000 miles, I rotated my tires and the death wobble...
  7. Anvil

    Front hub real time help

    I'm replacing the wheel bearings on my 97 80. The problem is... the hub will not go on far enough. There's no room for the adjusting nut. I've doubled and tripled checked the races are seated and the bearings are installed correctly. What am I missing? Thanks!
  8. Anvil

    Wanted  1995 Fzj80 gray drivers side seat belt

    Looking for a gray drivers side (front) seat belt for a 1995 Land Cruiser. Thanks!!
  9. Anvil

    Blue Sea 7610 alternative?

    I'm not having much luck with the longevity of the Blue Sea 7610. I'm not going to bash them... but would like to know what options you guys prefer. I really want to go with a different relay for my dual batteries. Thanks! :popcorn:
  10. Anvil

    Stereo install question

    I'm installing a new stereo and have a question... Where and how do I connect the parking brake and reverse light wires? Any help will be greatly appreciated!! Thank you!!! :popcorn:
  11. Anvil

    Real time troubleshooting help

    I have a 1997 80. I did a complete brake overhaul in September... new oem rotors and calipers, master cylinder, and EBC pads. Last night I came to a stop and heard a very LOUD grinding sound from the front right. I assumed a brake pad separated and the rotors was destroyed. Something was in a...
  12. Anvil

    High Water Mark Trail map

    Hi Guys! I know a few of you have run the High Water Mark Trail. Do any of you have maps to share? I'd like to run this trail in 2-3 weeks and start in Clayton, Oklahoma and work my way east. . I've been searching google but haven't found what I'm looking for. Any help would be much...
  13. Anvil

    Head gasket replacement question

    It's time to replace the head gasket on my 97 with 210k. I'm having a head rebuilt now and will be exchanging heads when I replace the gasket. I need to complete this task in two days. Here's the question... Do most folks leave the engine in place when replacing the head gasket, or remove the...
  14. Anvil

    Wanted  Head for 1997 1fz-fe

    Looking for a good head to rebuild for a 1997 1fz-fe. Thanks!
  15. Anvil

    Wanted  1997 Fzj80 rear shock mounting bracket

    Hello! I need the rear passenger side shock mounting bracket for a 1997 80. This is the bracket on top of the shock. Thanks! Edit... Found a bracket. thanks!
  16. Anvil

    Bosal 228-243 Exhaust Pipe

    For those of you who used the Bosal 228-243, the exhaust from muffler to tail pipe... Did your pipe have a flat spot? I returned the first pipe I ordered from Summit because it had a flat spot. The second pipe was order from a different vendor and was delivered today and has the same flat spot...
  17. Anvil

    A/C troubleshooting needed... it's getting hot in Texas!

    Please help me troubleshoot my a/c problem. Here’s the history… 2 years ago I replace the compressor with a new Denso compressor along with new fan, radiator, water pump, clutch fan, and new o rings in the ac lines. Had system charged with dye added. Last fall the ac started working...
  18. Anvil

    Wanted  Steering wheel for 1997 FZJ 80

    Looking for an tan/oak steering wheel for a 1997 FZJ 80. Doesn't have to be perfect. I intend to send off for recovering. Thanks!
  19. Anvil

    Temp sensor part number

    I've spent considerable amount of time trying to find this part number, and I now concede defeat. lol I'm sure it's here somewhere... Can someone provide the name or part number for this sensor? Thank you!
  20. Anvil

    Wanted  Wanted: 1997 1Fz-Fe engine

    Looking for a 1997 1FZ-Fe engine to rebuild for my 97. I'm not in a big hurry, but wanted to start looking. Please let me know what you have. Thanks!
Back
Top Bottom