Hi JAFO2014,
Thanks for your comment. Does it matter if I bring #1 piston either TDC or BTDC on compression stroke? The FSM said bring piston #1 to BTDC. Also, when dropping the dizzy, should the rotor be directly in contact with plug tower #1 or there should be few degrees lagging? BTW my dizzy...
Hi All,
Need help here. My '78 cruiser won't fire up after I re-installed the D.U.I. dizzy. I have to pulled-out the dizzy to remove the snapped hold down bolt. But before I pulled out the dizzy, I marked all the HT wires positions on the dizzy and spark plugs. I also remove the cap and mark...
Hi Mark,
Thanks for your advise. I will try to do the test and see. Also, I noticed that when my cruiser starts losing power, my brake also becoming so weak.
Regards,
Gado
Hi 40 Lovers and Enthusiasts,
I would like to refer to everyone my cruiser's current issue. I noticed that once the water temp. goes a bit under the half mark of the gauge, it starts to lose power. Does anyone have the same experience at some stage with their cruiser when the temp. goes up...
Hi Jim,
Love the look of your rig's soft top. I'm also planning to put in a soft top on my rig. Could you please post detailed pics of the installation? Especially how yoy installed the bows.
TIA.
Cheers!
gado
Gentlemen,
Just got me a brand new 12000lbs. winch. Stll trying to figure out will it sit on my 40's bumper. I wan't it a bit tuck into the bumper and front grill if possible. So, kindly show me what you guy's fot for your rigs.
TIA.
Cheers!
gado
Just a very timely thread as Im also planning to do a C&T on my 40. Gents, how did you prep the knuckle and housing for the C&T? Did you literally cut the housing or did you ground the welds and the knuckles will just come off the housing?
Kindly share how you guys done it.
Cheers!
gado
Gents,
I'm planning to replace my stock springs with a 2.5" lift leafspring. I just wanna see how would my rig will look like after the change-out. If you guys have done it, kindly share your pics. Mine is a SOA on 36" rubber.
TIA.
cheers!
gado
@kurtnkeggen, @davegonz, @65swb45,
It's an old set-up mate. SOA, not cut-n-turn, 36x12.5R15 Simex. Haven't experienced it when my set-up was a bit new. But now, it's kinda getting bad. And the ATF leaks badly at the seal of the worm gear.
cheers!
gado
Gents,
I'd like to hear from you guys about my problem recently with my rig's power steering system. I noticed that when i turn the wheel full right or full left, i can feel a strong wobble on the steering wheel. But I don't experience this while I'm driving straight on the road.
Does...
Sir burnttoastburgos,
I love it! Thanks for the pics. How did you do with the U-bolt? Did you bend it a bit? If it's still OK with you sir, can you please take a closer shot of how's the u-bolt was installed.
Will really appreciate it sir.
More power to you!
TIA
Cheers! :cheers...
Hi Mr. burnttoastburgos,
I really love your work on your rig. Very inspiring.
Sir, may i please request? Can you please share the picture of the front SOA conversion? I would love to have a close-up view of the conversion specially on the pumpkin side. Did you do a cut and turn?
TIA...
Hi matchan40,
May I please request
if you can just e-mail to me the pics taht i requested. Here's my e-mail add:
gado.velarde@gmail.com
TIA.
Cheers!
gado
Hi Eshu Elegua,
Can you please post a detailed and close-up picture of your soft doors? I'm planning to convert my hard doors to soft doors because i think it's already impractical to rebuild my hard doors considering the sourcing of door weatherstrips and bailey channel, etc. is very hard...
Hey matchan420, good day!
Can you please post a close-up view (multiple shots will be much appreciated) of the passenger side installation? And also, please write down the materials you used. Did you cut and turn? I'm contemplating of re-doing my SOA conversion on my 40. Hope you can share...
Sir,
Could you please post a close-up picture of the fron SOA set-up? It's so sweet. I would like to see how you done the perch and U-bolt installation if it's OK with you.
Congrats on your sweet project.
TIA
gado