Hi,
I am trying to pin down the identity of a left hand drive BJ40 that we have in the shop.
I cannot find any reference to the Unit. 140 or N-7397 on the ID plate in the engine bay and there aren't any other plates on the car.
Any pointers?
Thanks
We have a US spec 12/1992 FZJ80 here in the UK that has the exhaust with the twin manifolds, sensors and initial silencers and are struggling to find a replacement exhaust system.
Some muppet has cut the silencers out thinking they were catalytic convertors and the rest of the system isn't in...
We are in the process of rebuilding a 2H engine from a bit of a mongrel 40 series that came out of Africa and understood our supplier (largest after market supplier in Aus) could supply +1mm oversized pistons so we had the block bored out to +1mm whilst waiting for the parts to arrive.
It now...
Hi,
We are doing some work on a UK spec 1989 HJ60, model HJ60RG-MNW and it appears to have some chrome trim alog the sills and we are trying to find out it's origins.
There is no sign of it on the Toyota parts system, so wondering if anyone else has seen one of these before.
The other side...
Hi,
We are starting to get an increasing number of 40 series through our workshops over here in the UK and are looking for a US based parts supplier who holds plenty of stock and is also used to shipping abroad.
We have good links with Aussie suppliers, just trying to find someone similar in...
We have just been sorting out some coolant leaks on a 2001 UZJ100 and now it won't start giving Igniter Circuit Malfunction code for all the cylinders.
We had resealed the thermostat housing and also replaced a couple of the pipes at the back of the engine and that was it.
We clear the errors...
Hi,
I am working on a 1979 HJ45 from Aus and am trying to trace a voltage drop when the ignition is turned on.
With the ignition off i get the full 12.x volts to the ignition switch, the top 4 fuses, basically to everything that would normally get it.
As soon as the ignition is turned on the...
Hi,
We are working on a '96 FJ80 with the 1FZ-ZE that won't start.
Running diagnostics via the flashing check light brings up the code 99 which doesn't appear in any of the standard manuals.
Googling the code in relation to the engine brings up a reference of DTC B2799 - Engine Immobiliser...
A customer is having a problem with the blower motor on his aircon and before we start down the old fashioned route of ripping the dash apart to trace the wiring I was wondering if anyone here had any electrical wiring diagrams for the model we have.
Here are the details..
It's a UK spec...
Do any of you know if it is possible to get Solex security locks (see Solex Locks) to fit an 80 series?
The UK supplier doesn't stock any so I was wondering if anyone in the US did.
Thanks in advance.
Hi,
Do any of you have the koyo/timken or equivalent bearing numbers for the front and rear wheel bearings as well as the swivel bearings?
As far as I can tell on the EPC the front wheel bearings are similar to the 80 series, but it would be useful to get some clarification.
Many thanks.
Hi,
I'm looking for some recommendations for OBD scanning software and cables that I can run on my laptop as opposed to a dedicated unit.
Looking around there seem to be so many options for cables and software around on Ebay and elsewhere that it is difficult to choose what to go for...
Hi,
I'm after the numbers for the wheel, carrier and pinion bearings on a 1990 semi floating rear axle.
I have the Toyota part numbers, but actually want the actual Koyo or Timken part numbers so that I can source them from a local suppler here in the UK.
Any help would be appreciated.
Hi,
Do any of you know the numbers of the front and rear bearings for a '01 KDJ95R?
I have the Toyota part numbers, but ideally want to track down the Koyo or Timken part numbers.
Thanks.
Hi,
I'm slowly stripping the AHC off a '02 HDJ100 and have removed all the pipe work, accumulators, under chassis wiring, pump, etc.
All that I have left to do is to remove the fuses and the ECU.
I should be able to locate the fuses easily enough, but was wondering where the ECU is...
Hi,
Have any of you considered some sort of protective guard to protect the CV boots and driveshaft.
A group of us have been off for a play weekend (see Picasa Web Albums - Julian Voelcker - ELCO Weekend ...) and one of the group in a 100 series ended up with a tree branch wedging between...
I am organising a social and play weekend for UK and European based Land Cruiser owners. It's along the same lines and the Salisbury Plain play days that I have run in the past.
So if you are in the UK, have a Land Cruiser, then come along.
Full details are at: http://www.landcruisers.info.
Hi,
A friend has just had their 24valve engine overhauled at 300k with valve gaps checked, new cam belt, IP and injectors serviced, however the engine had major failures when tested by the garage doing the work.
'Allegedly'....
1. The rocker on the nr 2 piston came off + broke
2. Struck...
Hi,
I'm about to build a storage system for my 80 that I want to be able to transfer to my 100 when I get it.
If someone here has a couple of minutes spare and a tape measure, please could you measure the dimensions of the boot/trunk so that I can compare the two.
Below is a photo...