Search results for query: *

Forum search Google search

  1. Recon1504

    Builds 1985 BJ70 Story and Modifications

    Looking good Alberto...
  2. Recon1504

    Need 1971 Driveshaft Measurements

    The reason I was asking for stock 3 speed measurements, I was trying to establish a correlation between installed length versus fully collapsed length. Based on a couple of responses and a thread that I found while searching, I am using a 1" deduct from installed length to fully collapsed...
  3. Recon1504

    Need 1971 Driveshaft Measurements

    Changed out the pinion flanges to 60x68.5 bolt pattern and getting late model FJ40 driveshafts cut down to fit. not using any of the 3 speed stuff...
  4. Recon1504

    Need 1971 Driveshaft Measurements

    Those measurements are great. They, along with bikersmurf's post confirmed the 1" +/- difference between collapsed length and installed length. Driveshafts heading to the transmission shop this afternoon to get cut down and balanced...
  5. Recon1504

    Need 1971 Driveshaft Measurements

    That works for me. I've been measuring from center to center. I have a diagram that I can post tomorrow.
  6. Recon1504

    Need 1971 Driveshaft Measurements

    The lift will throw off the measurements, but your measurement will help me determine if the 1" difference is correct in a general sense.
  7. Recon1504

    Need 1971 Driveshaft Measurements

    I used the .pdf for the BJ frame that has factory measurements for the engine mount locations. They were located as close to the factory specs as possible. I did find in another thread today where it was stated that the fully collapsed length of the driveshaft should be approx. 1" shorter than...
  8. Recon1504

    Need 1971 Driveshaft Measurements

    Need the flange to flange (front) and the e. brake drum to flange measurements for a '71 (or similar setup) with F, 3 speed/T-case. Trying to figure out how much adjustment was factored in for a fully collapsed driveshaft to an in-place driveshaft. I am in the process of upgrading to a 3B/5...
  9. Recon1504

    Parting Out 1977 FJ40

    Driveshafts?
  10. Recon1504

    Parting Out 1977 and 1978 FJ40 Parting Out Entire Vehicles EVERYTHING!!!

    Front/rear driveshafts?
  11. Recon1504

    Parting Out complete '89 fj62, 300k, motor runs, bad trans

    Still have the power steering gear box? Condition? Price shipped to 43469?
  12. Recon1504

    Parting Out 89 FJ62 - Now in Fredericksburg, VA

    Still have the power steering gear box? Is this the later style with offset mounting bolt pattern? Condition? Price shipped to 43469?
  13. Recon1504

    Parting Out 1987 fj60

    Still have the power steering gear box? Condition? Price shipped to 43469?
  14. Recon1504

    Parting Out 88 FJ62 in Fresno

    Do you have the power steering gear box? Condition? Price shipped to 43469?
  15. Recon1504

    SOLD FJ62 Power Steering Gear Box

    Still available? Shipping to 43469.
  16. Recon1504

    Wanted 60x68.5 Bolt Pattern Driveshafts

    65wb45 - Do you still have the front driveshaft that is 32.5"? How much shipped to 43469? I know I will have to modify the rear (3B/5 spd transplant into 71 FJ40). Do you have another driveshaft with the 60x68.5 bolt pattern that is longer than 17.75"? Sorry for the long delay in my response time...
  17. Recon1504

    Wanted 60x68.5 Bolt Pattern Driveshafts

    The front is 32.5" flange to flange and the rear is 17.75" flange to flange.
  18. Recon1504

    Wanted  60x68.5 Bolt Pattern Driveshafts

    In search of FJ40/BJ40/42 driveshafts with the 60x68.5 bolt pattern
  19. Recon1504

    For Sale FJ40 front and rear driveshafts

    Still have these and what is the bolt pattern measurements?
  20. Recon1504

    SOLD FJ60/62 Parts Moving Sale (SoCal)

    Do you still have the driveshaft ends? If so, what are the bolt pattern dimensions?
Back
Top Bottom