Howdy all,
I've rebuilt my PS box on Marmaduke and I think it is toast. I have over 4" of steering wheel play in the input shaft with NO sector shaft movement.
Driving symptom are a floating feeling with slow wander left to right with wheel correction needed.
My guess is the gears have...
I'm still looking for a solution for the wiring that goes from inside of the truck to a roof rack mounted solar panel and LED lights
1) Easy to "undo"
2) waterproof
3) would like a solid mount on the truck side. I don't mind drilling holes.
4) 6 terminals would be great, 4 would work.
Any...
I have gotten rid of my vacuum brake booster and I have disconnected the vacuum line from the back of the pump on the alternator.
My question is can I just plug off the port and have no ill effect on the pump?
I haven't figured out a system for shutting off the truck, t-case shifting and...
OEM toyota exhaust brake (sold)
This is an exhaust brake for the 3B/1H motors found in the Dyna/Coaster busses.
I am getting rid of it because I am planning to get rid of all things vacuum controlled.
Here is a break down of all the parts I have for it:
46760-36250 Cylinder Assy...
Any reasonable offer considered. The more you take, the more you save!
Located in Saskatoon, SK Canada. Will ship Canada Post your cost.
one sets of brake calipers for cores SOLD
70 series air filter housing SOLD
BJ40 brake booster (MC is shot) SOLD
BJ60 brake booster (MC is shot) SOLD
BJ...
I have a pair of full floater rear FJ45 axles. Not sure of the years.
One is complete with third. I have never opened it up. $400
One is apart (complete) with no third. $400
Located in Saskatoon, SK
Only picture that I have. One is boxed up ready to ship. I can help with shipping...
I am trying to 3 link + panhard the front of my HJ61 and have a few questions. I have read Bellavista's suspension and coil over FAQ and I am gathering data to plug into his formulas to get spring rates and ride heights etc. My goal is to have a great on road driving truck, a good crawler and...
Used but in great shape. New shims, studs and a used set of knuckles included if you are going from small bolt pattern to big.
tapered for GM rod ends
$225 + shipping
I am using an AL bell housing from a 87 BJ70 on my engine out of 82 BJ60. The castings must have changed at some point because the LHS stiffener does not line up.
Is there a stiffener available for this block?
I have a rust free hatch and tailgate for trade if wanted. They do have a few dents but are off a JDM HJ61.
Looking for ambulance doors in NA or Aus.
Thanks for looking.
This engine has been off the road for the last ten years. Sitting in a heated garage. New sleeves, pistons, stainless precups, bearings, injectors, oil pump ect at time of rebuild. injection pump was rebuilt at the same time. Has the fancy shcmancy high nickel head out of Aus.
No...
I though I would post a collection of the mods I have done to my trailer since I brought it home. I hope this helps someone looking for any ideas.
I welded land cruiser spindle with a birfield shaft to a piece of 3" pipe for my axle. I will use a mini truck disk brake hub and lock out...
I bent the front axle housing on Marmaduke last summer and I finally have my Diamond housing under the rig. I need new shocks up front and in searching for those found air bump stops.
These seem like a good idea if I understand their use correctly. The reason I bent my housing was because...
One set of 27 spline cromo longfields and inner shafts for a 60 series axle.
Less then 50km on the birfields and the shafts have never been installed.
SPF
I have a pair of full floater rear FJ45 axles. Not sure of the years.
One is complete with third. I have never opened it up. $600
One is apart with no third. $550
Located in Saskatoon, SK
Would do a partial trade for a set of 80 series inner axles with long spline for a locker...
Located in Saskatoon SK, can help with delivery in the province or Calgary.
new doors $350 for the pair
glass is good
interior bits
body is ROUGH
front axle (no third) $250
rear axle (no third) $150
engine and tranny gone.
or is slow to shut off. Maybe 10-20 second delay after removing the key. I was thinking VSV but it appears to be working correctly. Or at least it is when I test it after the engine is shut down
I thought it was my ign relay, as that is what I am using to shut the truck off with, when I...