Both running boards and fasteners removed from a new 2016 4Runner Trail with six (6!) miles at the dealer. Toyota PN 51771-35200 & 51772-35200. Will deliver to metro Denver or Colorado Springs for $300 or pick up in Larkspur for $250. Will ship for cost of freight + packaging.
Best to email...
The above are from a new 2016 4Runner Trail and have 6 (six!) miles on 4, and 0 on the spare. $400 picked up in Larkspur, PayPal in advance (13-yr Mud member).
Best to email steve@restocustoms.com
303 681-1101 cell/text
Somehow critical parts were lost when my "new" 62 front hubs were disassembled (not by me). Anyway, I need two each of the parts in the box: Springs (2 different kinds), Pawls, & Clutches. The attached PDF from the FSM shows 'em.
Best to email me: steve@restocustoms.com
Thanks a bunch!
Anyone know where I can get them? MAF sells only their anti-inversion shackles for the 60 but not the shackle pins (their only 4+ pins are for the 40). I really like the design with the grease grooves, not to mention the hardened steel.
Gas gauge & clutch cover off my '83, tach off my '84 when we did the 3-way (Vortec & 4L60E>'84, '84 2F & 4-speed>'83). Everything works.
Temp gauge $10
Tach $15
Clutch cover $10
Best to email me: steve@restocustoms.com
I have the below VSV off my '83 60 & the following is inscribed on the plate (^ represents an "up arrow"):
Line 1: VACUUM ^ ^ T-0
Line 2: 084600-3330 12V
Line 3: NIPPONDENSO JAPAN
jmkfj60's has the following:
Line 1: E^ F^ G^
Line 2: 89570-60060
Line 3: 084600-3390 12V...
So I was crawling underneath the '84 trying to figure out how to route the air line for the rear ARB & spied this rust on the DS behind the crossmember that supports the park brake cable bracket. It's just in front of the front hanger for the rear spring.
How do I repair this the best way...
1983 FJ60 Engine Parts Plus...
AS OF 03/29/09: NO REASONABLE OFFER REFUSED! IT GOES BY 03/31 OR I'M THROWING IT IN THE DUMPSTER!
From my '83 60 (when it got the 2F from my '84):
Aisin carb $150 SOLD
Carb fan $30
Throttle linkage $10 SOLD
Gas pedal cover $2 (free with $20 other parts)...
RETURNED TO DOWNEY FOR PARTIAL CREDIT - THANKS, JIM!
The brainiacs that put the 5.7 Vortec/4L60E in my '84 FJ60 musta ordered everything they could think of from Downey & gave me the leftovers in boxes. Well, I finally decided to find out what it was, & lo & behold one box held a complete Fine...
Does anyone have a part # for the female fuse receptacle that fits the blank spots in the fuse panel for an '84 60? There are lots of blanks & I just hate in-line fuse holders.
Found out the yoke bolt pattern on my tcase is different than Turtle60's (who supplied a tcase half & yoke for prototype #1) so the TSM FJ40 tcase disc fits. Originally thought of mounting the cable to the frame but decided it wouldn't be good for the tcase brake to be activating when the...
Pair of semi-gloss black powder-coated brackets like these Rear Full Floater Disk Brake Conversion
Found out the hard way they won't fit a 60 FF. My loss, your gain. $50 + actual FedEx ground (I have an account).
Best to email me: steve@satelliteglass.com
Finally got off my a** & with the help of Spook50 made a decision on the type of adhesive & trim to use: McMaster-Carr 75875A661 1/8x3/8 butyl-coated sealing tape & 24175K17 edge trim.
So I searched & didn't find anything directly applicable. My trusty, "always starts" '83 "backup" 60 hardly turned over on New Year's after being driven a few hundred feet on Christmas. Few days later I checked the batt connections & cleaned 'em (didn't need it), put it on the charger, & snugged...
So I'm finally herding everything together for the serious brake upgrade & am looking for brake pad experiences. We're talking 4Runner calipers up front on a 62 axle, 60/62 calipers out back on a FF, Mountain 60/62 rotors all around, SS flex lines everywhere, & park brake prototype on the Xfer...
So I was amassing parts to be powdercoated yesterday for my suspension/axle/brake makeover & had a flashback looking at the 3rd member cases: they're different (d'oh)!
Back in my noobie days I posted up about the possiblity of going high-pinion & someone pointed out that if you flipped the...
Need glass only with good defroster lines & tabs. Can arrange pickup if in front range Colorado.
PM me with condition, location, & price as I won't be checking this thread that often.