Search results for query: *

  • Users: scoba
  • Order by date

Forum search Google search

  1. S

    What Did You Do with Your 80 This Weekend?

    The sealed area is created by pistons cylindrical side, rubber seal and the seal groove in the calliper if one of them is damaged it will leak.
  2. S

    105 Sector Shaft upgrade - Steering box rebuild

    When you remove preload nut is there just one bearing race under a thrust needle bearing so the shaft flange serves as the other side bearing race? I just disassembled mine and it's weird that the other needle bearing on the shaft has two races washers. Roman
  3. S

    105 Sector Shaft upgrade - Steering box rebuild

  4. S

    Builds 1-HDT rebuild - late 2019 start

    Any updates on your rebuild?
  5. S

    What Did You Do with Your 80 This Weekend?

    The motor is already out and half apart, inspect everything.
  6. S

    Front winch bumper design/build

    Great job. Nice light bar placement.
  7. S

    Merry Christmas! Free 80 Series Trim Gasket Set

    80
  8. S

    What Did You Do with Your 80 This Weekend?

    The first one is a real IH8mud picture
  9. S

    What Did You Do with Your 80 This Weekend?

    Had to replace front left wheel bearings. They were due to be replaced 100000 km back when I got the truck. But I ended up stretching it for a bit longer. They were KOYO made, really impressed with the performance. Installed TIMKEN in a good shape salvaged from my other 80 as a temp. solution.
  10. S

    What Did You Do with Your 80 This Weekend?

    Happy birthday!
  11. S

    Bannana needs help. 30mm crank bolt siezed?

    There is nothing to do with threads. the heat will expand metal and move head of the bolt away from the pulley which will make cracking it easy.
  12. S

    Bannana needs help. 30mm crank bolt siezed?

    Propane torch would not overheat your bolt. Apply heat for a minute or so from approximately opposite sides of the bolt head.
  13. S

    What Did You Do with Your 80 This Weekend?

    The engine oil pressure is too impressive for the fully warmed up engine.
  14. S

    Bannana needs help. 30mm crank bolt siezed?

    Heat up the bolt with propane torch (yellow bottle) direct the flame on to the head of the bolt perpendicular to it not towards the pulley so you do not damage the rubber, should be going easy after that. It worked for me.
  15. S

    The smell of ga$

    Search the posts, there is a few with similar symptoms. I have a “leaky” filler neck around the bend under the body. I live in Canada and vehicle is pure Canadian, so sault did it job pretty well. It does not leak all the time it even holds the vacuum in the tank but when I overfilled once- it...
  16. S

    Power steering leak

    A couple of days ago my :princess: was going to pull off the driveway in the morning but the few minutes later she was back asking why she could not turn the steering wheel. When i went to see what is going on i found a puddle of steering fluid under the vehicle. So I looked under the hood. One...
  17. S

    Head gasket ?

    Engine head cracked I started this thread a while ago but did not post the cause of a trouble. Trouble was caused by a crack in the head between plugged hole and mount hole. I made picture and saved it on a disk but since I moved to a new place I could not find it. So I gave up on finishing...
  18. S

    O2 sensors replacement

    Thanks for advice, I'll try it today and post the result. I still have to post my HG unusual story.
  19. S

    O2 sensors replacement

    It is 97 LX450 220 km, Gas, stock, used to have 12.4 mpg now 9.5 mpg. MPG got worst after HG job was done. Then Check Engine started to come on once in a while, then it came on and did not go away for a long time, then I replaced O2 sensors, Check Engine went off right after replacement, but no...
  20. S

    O2 sensors replacement

    I replaced two O2 sensors. Check engine light went off. But MPG is still very poor. Does computer keep in memory the code even so the check light is gone?:confused:
Back
Top Bottom