Search results for query: *

  • Users: NZBJ71
  • Content: Threads
  • Order by date

Forum search Google search

  1. NZBJ71

    Converting Aisin winch motor to series wound

    Hi. Curious if anybody has converted the factory 80 series a1-1000 winch from a permanent magnet motor to series wound? I have issues with the winch locking up under load and not spooling out. Pondering options for a bit more HP. I really like the freespool on the Aisin but I need better...
  2. NZBJ71

    RCV 30 spline Birfield on a Longfield 30 spline inner axle, will it fit?

    I am looking to install some longfield/rcv birfs in my 40 series but I have a problem that I have a BJ70 series front housing with a cable locker. I can get a Longfield super set and a longfield inner axle with a long spline. I can get a RCV ultimate set but don't know if there is any long...
  3. NZBJ71

    1H-FT iNJECTOR PUMP MISTERY DIAPHRAM

    Hi All, I recently upgraded from a 1991 HDJ81 to a 1996 HDJ81 with the 1HD-FT engine. The 1HD-FT is a bit sluggish off the line and I'm going to tweek the fuel pin to see if I can improve it a bit. There is a vacuum diaphram mounted above the injector pump and I can't figure out what its...
  4. NZBJ71

    80 series Aisin factory winch locking up under load

    Hi Folks, Whilst out on a trip a few weeks ago I managed to get the 80 stuck in a tricky hole with sucking porridge in the base an a near verticle 12inch step out. So I ran out the Factory Aisin winch an proceeded to attempt to winch out. The ting is the winch loaded up and slowed to a near...
  5. NZBJ71

    1HDT power steering pump - interchangable parts

    Hi all, I have a delema in that the powersteering pump on my 1991 HDJ81 landcruiser has packed a sad. I have striped it down and there is definate wear on the vane pump Cam Ring, the inner surface has waves. I haven't been able to locate a replacement pump at this stage and Mr Toyota...
  6. NZBJ71

    1990 hdj81 speed sensor output

    Hi all, i have a friend with a 350 powered 80 series running a t700 trans and B&M lock up control. however the lockup control isn't working correctly. we.ve had a poke around a found that the original speed sensor for the t700 transmision is still attached to the controller and not the drive...
  7. NZBJ71

    OEM Fatory Electric winch spool direction

    Here's a simple one for those with an OEM electric winch. Does the cable on the OEM winch spool off the top or off the bottom? I am as i an in the middle of making a mount to fit the factor winch to a TJM Alloy bar, The winch i have got is spooled with the cable off the top but every other...
  8. NZBJ71

    Electrical gremlins

    Hi I am having an electrical gremlin that is starting to hack me off. The symptoms are loss of electrical power after 15-20 minutes of running, the volt guage drops off and the vehicle will stall out at idle. On the surface appears that the alternator isn't charging, however i have had...
  9. NZBJ71

    KZJ78 crownwheel and pinion

    I have a friend who has shagged his crownwheel and pinion in his KZJ78 - Diff code G284 (elocker). I am trying to locate him a replacement gear set and have found one which i think is from is from a non locker model. the elocked gearset is the same as the turbo/v6 diff which is heavier than...
  10. NZBJ71

    HELP - GM V8 EFI issues

    Here's one for all you EFI V8 experts out there. I have a Holden 5litre EFI V8 (Holden is a branch of australian GM). Its basically and SBC block with their own heads and is 304ci. It uses a GM 1227808 ECU. The engine developed a stumble once up to temp (running for 10 or so minutes). this...
  11. NZBJ71

    Interchangability of Hubs

    I have just transplanted a BJ70 front axle into my FJ40 to get disks, PS and cable locker and i was just pulling the old assembly to pieces to recover spare CVs etc. My question is are Drum front hubs interchangeable with disk hubs? and are the also similar to FF rear hubs. Its that i would...
  12. NZBJ71

    1kzte - engine knock

    evening all I have a KZJ71 1994 with a 1KZ-te that has recently developed a concerning knock. The knock is regular at idle and there appears to be more vibration than usual. The knock sound like its coming from the bottom end and i have just pulled off the sump but nothing is jumping out at...
  13. NZBJ71

    Cable Locker - level location

    Cable Locker - lever location Hi all, a long time lurker here with a simple question I have just picked up a front cable locker out of a 198? BJ71 that i am going to fit to a 1982 FJ40 along with the power steering and front disk brakes. I all ready have a lokka (lockrite copy) in the rear...
  14. NZBJ71

    chevy V8 conversions

    Hi my 13bt in my BJ71 is slowly dieing (260000km) and is also not really up to the sort of driving i am aiming at doing now, particularly as it does not rev high enough to effectily clear the tyres. I have access to a 350 - 4speed bell housing. My main question at this stage is does...
  15. NZBJ71

    13bt Water Pump

    Howdy the seal on my 13bt water pump is started to leak. does anyone know if the water pump is serviceable or a throw away part? i'd like to also thank Mr Toyota in making another part that involves removing half the engine bay to remove. Cheers Tony
  16. NZBJ71

    PTO Drive gear Part number

    Howdy Does any one know the part number for the PTO drive gear for a 70 series transfer box? This is the gear thats the main shaft that drives the PTO box not the PTO box itself. Thanks in advance. Tony
  17. NZBJ71

    BJ71 Transfer case rebuild

    My Transfer case is shot and making very bad noises and there is a little more play in the output shafts than i like to see (in that there is any). Im going to do a rebuild in the very near future. My question is can this be done on the vehicle or do i have to pull the transmission?? cheers...
  18. NZBJ71

    Pionion bearing replacement

    Howdy all, I've been lurking around for some time with little to add so haven't been posting but have been sucking up your knowledge like a spunge. Problem i have is that i have a rumbling comming from front when in 4wd, only seams to come when not under load. I've had a feel an suspect...
  19. NZBJ71

    Puttinh 35's under a BJ71

    Just looking at new tyres for BJ71 and was wondering if a lift is required to fit 35's, (currently on 31x10.50 BFG). i am running reset springs with 1" lift so would they fit without any extra lift and/or what sort of rubbing should i expect?
Back
Top Bottom