Search results for query: *

Forum search Google search

  1. NZBJ71

    Converting Aisin winch motor to series wound

    Hi. Curious if anybody has converted the factory 80 series a1-1000 winch from a permanent magnet motor to series wound? I have issues with the winch locking up under load and not spooling out. Pondering options for a bit more HP. I really like the freespool on the Aisin but I need better...
  2. NZBJ71

    80 series Aisin factory winch locking up under load

    Greetings, I still have the same winch, though on a newer 80#, I haven't had the winch completely lockup in a couple of years but I am very aware of the potential for it to so tend to not load it up to the same extent, and if its going to be a hard pull I double line it. In short I don't...
  3. NZBJ71

    RCV 30 spline Birfield on a Longfield 30 spline inner axle, will it fit?

    I am looking to install some longfield/rcv birfs in my 40 series but I have a problem that I have a BJ70 series front housing with a cable locker. I can get a Longfield super set and a longfield inner axle with a long spline. I can get a RCV ultimate set but don't know if there is any long...
  4. NZBJ71

    1H-FT iNJECTOR PUMP MISTERY DIAPHRAM

    The vacuum line run from the vacuum pump and to the pump below the diaphram. So i think it must be the High Altitude Compensator. Not sute how it knows its at altitude as it only has a vacuum line in and out?
  5. NZBJ71

    1H-FT iNJECTOR PUMP MISTERY DIAPHRAM

    Hi All, I recently upgraded from a 1991 HDJ81 to a 1996 HDJ81 with the 1HD-FT engine. The 1HD-FT is a bit sluggish off the line and I'm going to tweek the fuel pin to see if I can improve it a bit. There is a vacuum diaphram mounted above the injector pump and I can't figure out what its...
  6. NZBJ71

    Electric Winch Owners - Problem Spooling out under Heavy Load?

    I pulled mine apart the other night to better figure out the inner workings. I found a couple of things, Firsty the side flange of the drum was buckled and has been rubbing on the end housing, this may have been binding. so a big spanner bend that straight again. Second is that when in...
  7. NZBJ71

    Electric Winch Owners - Problem Spooling out under Heavy Load?

    Yes, haven't found a practical solution yet 80 series Aisin factory winch locking up under load
  8. NZBJ71

    80 series Aisin factory winch locking up under load

    You must have missed my signature, I already have a VJ40 with PTO but it doesn't fit the family very well as the rollcage gets in the way of the rear seats. And I used to own the BJ71 that went around me. Back to the issue at hand. this is what the reverse clutch looks like. It cams back...
  9. NZBJ71

    80 series Aisin factory winch locking up under load

    Hi Folks, Whilst out on a trip a few weeks ago I managed to get the 80 stuck in a tricky hole with sucking porridge in the base an a near verticle 12inch step out. So I ran out the Factory Aisin winch an proceeded to attempt to winch out. The ting is the winch loaded up and slowed to a near...
  10. NZBJ71

    Check out what my gas gauge can do.

    check the bottom of your tank, Its almost certianly got a big dent. When you give it a good dent the baffles/surge pot get out of line and the sender gets stuck on the side. Fix is to panel beat you tank or bend the sender so that it doesn't get stuck. Your tank will also hold less
  11. NZBJ71

    1HDT power steering pump - interchangable parts

    Hi all, I have a delema in that the powersteering pump on my 1991 HDJ81 landcruiser has packed a sad. I have striped it down and there is definate wear on the vane pump Cam Ring, the inner surface has waves. I haven't been able to locate a replacement pump at this stage and Mr Toyota...
  12. NZBJ71

    Door Frame Help (Pic)

    Is the screen hittting your front roll cage hoop? This happened on a cruiser I bought, I had to shorten the roof bars and lean it back slightly Tony
  13. NZBJ71

    Castor Correction in New Zealand

    Get your mate to go to BNT or repco, he can get offset bushes through them. Anyone with a press can change the bushings easily. Alternatively depending on lift ie more then about 75-100mm he will need drop boxes or castor plates, Just jump on the net and get them from an oz or possible...
  14. NZBJ71

    1990 hdj81 speed sensor output

    Hi all, i have a friend with a 350 powered 80 series running a t700 trans and B&M lock up control. however the lockup control isn't working correctly. we.ve had a poke around a found that the original speed sensor for the t700 transmision is still attached to the controller and not the drive...
  15. NZBJ71

    OEM Fatory Electric winch spool direction

    Here's a simple one for those with an OEM electric winch. Does the cable on the OEM winch spool off the top or off the bottom? I am as i an in the middle of making a mount to fit the factor winch to a TJM Alloy bar, The winch i have got is spooled with the cable off the top but every other...
  16. NZBJ71

    Electrical gremlins

    Their is very little of the factory electrics still in place and the vehicle has a volt meter installed on the dash. When i refer to loss of electrical power basically the volt meter drops from 14v (normal running) down to 10v or less. With the electric fans, fuel pump, efi running and...
  17. NZBJ71

    Electrical gremlins

    Hi I am having an electrical gremlin that is starting to hack me off. The symptoms are loss of electrical power after 15-20 minutes of running, the volt guage drops off and the vehicle will stall out at idle. On the surface appears that the alternator isn't charging, however i have had...
  18. NZBJ71

    KZJ78 crownwheel and pinion

    Thanks for the replies guys, have checked an vehicle with open diff and it is the turbo diff, so i'm all good. Thanks again Tony
  19. NZBJ71

    KZJ78 crownwheel and pinion

    I have a friend who has shagged his crownwheel and pinion in his KZJ78 - Diff code G284 (elocker). I am trying to locate him a replacement gear set and have found one which i think is from is from a non locker model. the elocked gearset is the same as the turbo/v6 diff which is heavier than...
  20. NZBJ71

    Spring Flip questions

    Cut and weld steering components If you are going to have this vehicle road legal in NZ there is basically no way you can weld any of the steering components. I'm not entirely sure i understand your question but a flatter steering arm from the box may resolve conflicts. on another note...
Back
Top Bottom