https://forum.ih8mud.com/threads/buy-sell-trade.931565/page-23#post-15257399
Post #458
some hard to find items and project ideas that will never become projects.
Hi,
I have a New In Box CTEK 250SE. This charger is smart enough to charge dissimilar batteries - start and deep cycle. Without a unit like this your house battery never really fully charges. I have used them successfully for my overlanding rigs. Simple install too.
I don't have time to...
I'm doing my research right now for doing an LS conversion on the LX. It is a common conversion and the path that others have travelled will benefit me as I contemplate what I have to purchase and prepare for.
I'm sort of mixed on the approach . Crate gets a little expensive (up to 20k), so...
Hi All,
I'm getting ready to modify my FJ Cruiser 17's to accept the 40 series hub caps. I really like the look of the early acorn style.
I've seen a number of threads and forums where people have modified these wheels with clips but the hub cap always shown is the later style with the...
Trouble shooting..... fuses good, haven't checked my tow harness but will get there. Much less trouble to put in a new relay for signals as a first diagnose.
I'd be grateful if someone knows whether the relay serves both signal and hazard? I assume so but I've wrong many times before.
Thanks
Hi Mud,
I'm having trouble with my heat. Blows cold or hot and not in between. All the threads I've read have helped me confirm its the servo motor...in particular the one that sits on top of the heater core housing. However, none of the threads I've read list the toyota part numbers.
I...
Today I picked up my new Roofnest Sparrow Eye in black. Sparrow Eye Roof Top Tent - 82" x 46" - Sleeps 2 | Roofnest
The struts are weighted perfectly - the first opening was a gentle nudge and it effortlessly lifted up. Purchasing sight unseen is always worrying but first impressions is that...
two four speed transmissions with coarse spline for 2F
One is known and had a dealer rebuild - missing t-case. This is the long unit from a 1986
One is unknown and has t-case from a 1982 short tranny - no bell housings for either
4:11 front diff in great condition with factory LSD shims...
So I've tried various mounts including ram, magnetic etc but I have yet to be satisfied with the lack of wiggle for a tablet and I like using my tablet for GPS.
I have the factory grab handle and went off of it with a ram. Used a ram off the floor, used a ram off my console. The further a...
Looking for a 5 speed front drive link (picture from Toyodiy) part number 36337-60060. This is the link that attaches the transfer lever to the side of the transmission
Its the highlighted piece in the pic below - 5 speed is different than four speed
Hoping to find a 5 speed front drive link (pick below from Toyodiy) part number 36337-60060. This is the link that attaches the transfer lever to the side of the transmission
Its the highlighted piece in the pic below - 5 speed is different than four speed
I have a 5 speed transmission from an HJ60.
Noted that the transfer lever is different than the four speed and I'll have to source it.
I need a shifter lever as well
Any one know what years they were here so I can search toyodiy?
Anyone have these parts?
Thanks
My 2f is no where near stock configuration any more; I'm using a Downey's air cleaner and other bits.
I'm just about done assembly and have chosen a breather.
I do not want to run hose all over and would not be able to secure it well either. The stock configuration runs a hose from the valve...
UPDATED
My 2f has been desmogged and is running a holley.
Previous owner cut the factory metal line from the fuel pump and I have to go from it (ends close to the water pump) to the carb with a rubber hose.
I have two THREE choices,
make a new metal line that I would support off the intake...
Hi all, Seems like a dumb thing to ask - but I missing something on my motor.
My 2F came to me without truck and was just the motor and tranny. I'm scratching my head and searched a number of threads for pics but can't find a clear shot of how the lower hose metal pipe is bolted.
Looks...