Hi all--Chasing a P0125 on my 1996 LX 450. It was intermittent, then the other week it became permanent and the truck started to run very rich (by smell), rough, missing, etc. Checked upstream O2, found signal wire hanging by a corroded thread, replaced the harness side connector.
Started it...
Hi all--Please see my Craigslist ad for more detail and photos, but briefly, I sold a 1970 FJ40 project and no longer need these new reproduction panels.
https://minneapolis.craigslist.org/ram/pts/d/saint-paul-toyota-fj40-land-cruiser-new/7632475193.html
rear quarter panels $300/pr
driver's...
Hi all--Due to unforeseen personal circumstances, my 1970 FJ40 basket case needs to move ASAP. See thread here: 1970 “it’s all there, I swear” project - https://forum.ih8mud.com/threads/1970-its-all-there-i-swear-project.1289702/
Disassembled, rusty but complete truck. Engine starts and runs...
Hi all--I recently purchased a partially-completed project truck which included an AFI fuel injection system. As far as I am aware, this was never fired as it was not plumbed for fuel or had the electrical fully connected. The underhood components were installed in the truck and so there is some...
Hi all--I bought a partially-completed expedetion/camping/overland truck and am going in another direction with it, so selling a Blue Sea "automatic charging relay". Includes everything pictured in the product listing on Amazon (https://www.amazon.com/dp/product/B001VIXLRO?th=1) as well as a...
Anyone have (or have links to) some nice shots of the carb, manifold and linkage area from a factory 2F FJ55? Trying to bring my engine (1978) back to stock-ish state from a pile of parts. Search turned up a few shots but mostly incidental, zoom-in sorta deals from various ads.
Thanks for any...
Hi all--Asking in the 40 forum for more visibility:
I just bought an FJ55 that someone began converting to fuel injection using the AFI kit. The truck has a DUI distributor installed but the unit has no vacuum advance and instead a 6-ish wire connector that was running into the AFI wire...
Hi all--I have been fighting coolant leaks on my 1979 FJ40 this past month and am fed up.
Worm gear clamps back off, crack and rust(!?), what are you all using instead? OE style? Non-worm band clamps?
Interested in opinions, I don't care if it's OE or not, looking for good value for my dollar...
HI all--Interested in restoring my 1970 to column shift and have zero parts. Anyone have a setup they'd like to sell? Could potentially (partially?) trade my floor shift if that helps, but not necessary.
Thanks.
As seen in this post (labeled in big red letters): ( Update )Carburetor question - https://forum.ih8mud.com/threads/update-carburetor-question.994495/#post-11056634
I have a 1970 carburetor in need of a throttle cable bracket. Anyone have one they'd part with? Thanks.
Hey all—Bought this locally from a guy who wasn’t able to complete. Rough but quite original and everything appears to be included, some assembly required. Also came with almost all the needed sheet metal and was a running/driving truck when torn down.
Goal is to put it back on the road in...
Hi all--Just bought a 1970 FJ40 basket case with a GM Rochester carb. I would like to go back to stock, rebuildable core is fine, I am comfortable doing the work.
I believe I need everything except the throttle cable (so cable brackets, riser(?), etc.--I have the air cleaner and the intake and...
Hi all--Finishing some major work on my '79 FJ40: rebuilt cylinder head, rebuilt carb, belt drive fixes, proper desmog (PO had done it about halfway and poorly).
Following the excellent 79-80 "definitive guide" here, and in this post in particular the HIC vacuum routing is described: The...
Following the guide here: How to adjust your 2f valve clearance - https://forum.ih8mud.com/threads/how-to-adjust-your-2f-valve-clearance.1152737/
1979 FJ40. My distributor is I think not stock. It is points only and the igniter has been removed. Cap is made in USA and has no provisions for...
Posting in case others don’t feel like screwing around and buying unnecessary $5 bolts. And so I can find this again once I forget.
Mounting a 2F to the HF stand requires:
- HF Pittsburgh heavy duty “1/2 ton” stand, the version with four wheels.
- 4x M12x80mm, 1.75 pitch (coarse) flange bolts...
Hey all--1978 FJ55 (inop but complete, sealed roller) transport needed. Beverly, MA to Saint Paul, MN. 33" tires and a roof rack, seller states 6'5" overall height. Packed with interior and some spare parts, nothing heavy like driveline parts or extra wheels etc.
Seller able to assist loading...
Hi all—New owner of a triple-locked LX 450 here. Needs lots of attention but the bones are all there and I got a very reasonable deal on it.
It’s got mismatched and absolutely shot 35x10.5 tires on it, so a lift of some sort I would think. Considering going to 315/75-16s as a replacement.
The...