Search results for query: *

Forum search Google search

  1. S

    Pre-03 nav delete how-to

    Any chance you could try your magic at finding the female connectors? I’ve found the versions that require soldering to a circuit board but not on that can be connected to loose wiring. I figure if one could get their hands on the female connectors, they could build a custom harness and this...
  2. S

    New wheel options 100 series FN wheels Six Shooter and Five Star

    Have you gotten these mounted up yet?
  3. S

    New Bi-LED head lights

    I see that about the bulbs. Contemplating a quad H1 Bi-LED Setup now. 🤣
  4. S

    New Bi-LED head lights

    Why did you decide to go bi-led vs bi-xenon? I'm intrigued by this setup as its using the H1 size base. I wonder how these compare to a D2S setup.
  5. S

    (yawn) Another 100 gets built

    Thanks for getting that. Would you mind getting the measurement of the area of wheel where the TRD cap snaps in? I’m hoping it is greater than 92mm. The aisin hub is just under 92mm.
  6. S

    Tandem Off-Road Introduction

    @mexellent i know it’s been a minute. Will Tandem be releasing a 5x150 17x8.5 +25 ever? If so, “take my 💰!” 😁
  7. S

    What have you done to your 100 Series this week?

    The Method MR314 I was wondering about has a 110.50 bore. I was wonder if the flange bolts clear the 110.50 as some wheels taper to a little bit smaller bore due to the center cap (which of course wouldn’t be used in this case with the part time kit).
  8. S

    LC100/LX470 Part-Time Conversion Discussion

    I saw that the rock warriors taper down to an approx 95mm bore. I wasn’t sure if the part time portion would fit through that. The picture here is with either 1.25 or 1.5 in spacers.
  9. S

    LC100/LX470 Part-Time Conversion Discussion

    @cruiseroutfit do you know if the center bore of the Rock Warriors is wide enough to fit the part time hub? I’ve seen the build you included in a FB post from 7.20.22 where the owner used spacers. Do you happen to know what size spacer is required to run the part time kit and rock warriors?
  10. S

    (yawn) Another 100 gets built

    Are you running any spacers? If you have calipers would you mind getting the diameter of your AVM hubs? I’m wondering if my aisin ones will clear.
  11. S

    Chasing the Elusive 100 Series Rear Wind Deflector

    You could get the Massive Metal Shop light mounts that are meant to mount in the black flat air deflector mounts. Drill four holes in your air deflector and mount to the light mounts.
  12. S

    What have you done to your 100 Series this week?

    Do you mind posting a close up detail shot up of the front wheel? I’m looking at installing a part time kit and want to make sure it’ll clear the bore.
  13. S

    LC100/LX470 Part-Time Conversion Discussion

    Other than OEM options, what wheels are people running with their part time kits? I've seen the Rays and SCS offerings. Anyone get Method wheels or other brands to fit? I'm looking for a 17 with preferably a positive offset.
  14. S

    (yawn) Another 100 gets built

    What size spacers are you running? Did you have to machine out any of the bore to get the part time kit to fit?
  15. S

    New wheel options 100 series FN wheels Six Shooter and Five Star

    Got any close up pictures of the front and rear wheels separately? I’m about to install part time hubs on the front and want to make sure they will fit.
  16. S

    What is your experience with significant increases in unsprung weight and rotational mass?

    They are coming back. I hit them up on IG about it. Sometime soon.
  17. S

    BucFL LC100 Build

    @bucfl How have the NAPA calipers held up?
  18. S

    CV axels a “new” option?

    Did the part number for your outboard shaft and boot kit end in a 5 or 6? (If you recall).
  19. S

    100 Series LC OEM CV Axle Rebuild with FACTORY Shaft Assy. Outboard Joint 43460-69145

    As part of my brake refresh project, I’m rebuilding the CVs on my 208k 02 LC. New flanges are on order as well. The first post here referenced j43460-69145 for the outboard shaft kit. 43460-69146 also comes up for the outboard shaft but it’s a little higher in price at my local dealer. Anyone...
  20. S

    For Sale Northern Virginia - OEM 2017 200 Series Wheels x 5

    I’m interested. Can you post a pic of which style rim you have?
Back
Top Bottom