Search results for query: *

Forum search Google search

  1. 8

    1FZ trans swaps 6R80 10R80 and more

    Those adapters look great! The wiring for the analog paddles is quite simple, + - and Ground. I ended up designing my own fully adjustable paddle shifters: You can save a substantial amount of money by designing and 3D printing your own parts, but there are also some nice paddle shifters for...
  2. 8

    1FZ trans swaps 6R80 10R80 and more

    The adapter really looks like has been machined inverted... At least is just the aluminium plate that bolts to the main body of the adapter. I´ve stumbled upon Mr. Murphy´s law quite a few times on my project... The worst time being a typo error when I transfered the gearbox output shaft length...
  3. 8

    1FZ trans swaps 6R80 10R80 and more

    Those adapters look great! I was looking closesly at the tcase adapter image an the HF2A side looks like it´s been flipped 180 degrees, as if it had been mirrored compared to the cad image: Maybe It´s me or the image has been inverted...
  4. 8

    1FZ trans swaps 6R80 10R80 and more

    My idea is to install a sim racing paddle set directly on the steering wheel. I have an OMP style steering wheel and it is pretty easy to drill a couple of holes to install a paddle shifter set like the one below: There are many options available for around 100-150 eur, but I might as well...
  5. 8

    1FZ trans swaps 6R80 10R80 and more

    I´d rather not modify the shifter plate, it really looks like its a mess to do so... The manual shifting is quite simple to implement actualy. The turbolamik TCU has a couple pins specifically built for paddle shifters, wich are just two momentary switches with a common sensor ground: There...
  6. 8

    1FZ trans swaps 6R80 10R80 and more

    The 25mm hole for the starter pinion also lines uo with a dowel pin, but the LR has 4 dowel bores in total, so there is no problem using 3/4 dowel bores. About the exposed pinion, I´ve planned on designing a kind of dust plate, but this is not a major issue. I´ve just figured how to use the...
  7. 8

    1FZ trans swaps 6R80 10R80 and more

    Thanks for the appreciation! The Land Rover 8HP certainly made the job a lot easier. There are lots of holes, so in case a gerabox bolts lines up with an engine block bolt, there are many other gearbox holes that fit just perfect. In my case, I´ll have to drill a 25mm thru hole on the...
  8. 8

    1FZ trans swaps 6R80 10R80 and more

    Hi! Loving the thread! I´m also swapping a 8HP70x on my J80 Land Cruiser, only that mine is a 94 HDJ80. I´m not trying to hijack the thread or anything closer, but I´ll share some info on my set-up, in case there is some useful info for the 1FZ guys. Here in Spain, most of the 8HP gearboxes...
  9. 8

    A442F Output spline tooth count

    Hi I am in the process of mating a non-Toyota automatic gearbox to a HF2A transfer case and I reached the point where I need to fab the tcase adapter plate and mating shaft. Does someone know the spline sizing of the A442F? I assume that the output shaft from the A442F is based on the JIS D...
  10. 8

    1HD-T Transmission bolt pattern

    Hi As the title suggests, I am looking for the transmission bolt pattern of the 1HD-T engine found on the HDJ 80s. I´ve found the HF2A bolt pattern on this forum (NV4500 swap thread), but no luck at all for the engine bolt pattern. Anyone have the bolt pattern for this engine? Thanks!
  11. 8

    HDJ80 Throttle position sensor

    Yes, 1HD-T turbodiesel engine.
  12. 8

    HDJ80 Throttle position sensor

    Hi. I am planning on installing a different automatic gearbox on my 1994 HDJ80 and I need to install a TPS sensor for the new gearbox. I noticed a TPS sensor already installed on the injection pump (my car is an automatic from factory). My question is, does the original TPS send its signal to...
  13. 8

    NV4500 to HF2AV Open Source Adapter Plans

    I was talking about the HF2A bolt pattern shown in the first few posts of this thread. I am not swapping a NV4500 transmission, so I only need the bolt pattern coordinates fot he HF2A, sorry.
  14. 8

    NV4500 to HF2AV Open Source Adapter Plans

    Hi! I am swapping another gearbox into a hdj80 and I need the bolt coordinates of the HF2A gearbox. Are the coordiantes included in the first PDF of this thread accurate? Has someone machined an adapter based on those hole coordinates? Thanks!
Back
Top Bottom