Search results for query: *

Forum search Google search

  1. Wookie3011

    Got these for the 470

  2. Wookie3011

    Got these for the 470

    Talked to the shop. They offered to have them repaired. I counter offered to have them do my alignment and install 333 Fabrications cam eliminator.
  3. Wookie3011

    Got these for the 470

  4. Wookie3011

    Got these for the 470

    I ordered the Relations Race RR5H in Gunmetal. Using Falkens as tires. Unfortunately the shop that mounted the Tires gouged the crap out of the wheels. Is this normal for Aluminum? It is fortunately all on the backside of the wheels .
  5. Wookie3011

    New to the Forum

    Alignment Specs? I'll give Ironman a call as I didn't see any with the products recieved.
  6. Wookie3011

    Rust on GX 460

    Personally I searched High and low for a rust free GX470 in Kansas. In the end it was more of a compromise instead of rust free. I have what you have pictured and have spent the last week doing a lift on it. As I'm adding new components I'm wire wheeling brake clean blowing then treating with...
  7. Wookie3011

    New to the Forum

    Just doing the finishing touches on the IronMan lift. The issues I was having with my back shocks was due to the rear end moving 1-2" back on the driver side and since it's tied to a fulcrum point it's the opposite on the passenger side. Have to jack it back up in the rear and do some trailing...
  8. Wookie3011

    New to the Forum

    Good to know! Still messing with the front now. I noticed my rear axle is cocked about an inch. I'll try to adjust it out with the trailing arms. The upper control arm ball joint was seized solid and it took a heck of alot to finally get it to break free. I'm going to run up and get a ball joint...
  9. Wookie3011

    New to the Forum

    I really struggled with the install on the rear today. It just didn't seem like the shocks lined up correctly. I had to connect the bottoms and pull the tower bolt through in order to put them on. I did notice that I have 2 supports? Connected at the top of the rear Diffrential setup as well as...
  10. Wookie3011

    Builds Dissent offroad 2005 gx470 build.

    Deleted
  11. Wookie3011

    Builds Dissent offroad 2005 gx470 build.

    I really struggled with the install on the rear today. It just didn't seem like the shocks lined up correctly. I had to connect the bottoms and pull the tower bolt through in order to put them on. I did notice that I have 2 supports? Connected at the top of the rear Diffrential setup as well as...
  12. Wookie3011

    Builds Dissent offroad 2005 gx470 build.

    What is it and how much?
  13. Wookie3011

    New to the Forum

    Just so I know we are on the same page. I own a non KDSS Model. Does this still apply? I would be more apt to weld than bolt. More permanent and structurally sound. Thanks
  14. Wookie3011

    Builds Dissent offroad 2005 gx470 build.

    Still working on lifting it for now. Wheels and tires are next then bumpers.
  15. Wookie3011

    New to the Forum

    All the IronMan 4X4 Goodies getting ready to raise the bar! There are quite a few parts like panhard bar and swaybar extensions that I'm still trying to understand how to get these dialed in correctly. She's going straight to a alignment shop either way.
  16. Wookie3011

    Builds Dissent offroad 2005 gx470 build.

    Got me very old thread:(
  17. Wookie3011

    Builds Dissent offroad 2005 gx470 build.

    Very interested in this! Love it! Here's the new Amada Ensis 4020 AJ, also have the Bystronic 4020 and a old faithfull Trumpf dirty 30.
  18. Wookie3011

    New to the Forum

    I've been reading alot on here. I'm from Olathe, Kansas and just purchased a 2007 GX470. I have sitting in the garage a Ironman 4X4 Stage 4 FoamCell lift kit for it. I'll post pictures of it when it's done. Nothing you haven't all seen before:) she has 182k miles on her and ZERO rust. That was a...
Back
Top Bottom