Looking for a complete original wire harness for my 72' 40. I've already got a decent one that I'm going to pull out of my truck but I know it's seen its share of mods, etc. Would be beneficial to have a complete stock one on-hand that's all original.
Thanks. J
Looking for a charcoal canister for my '72 40. I believe the Toyota part number is 77740-60010.
Also, a fuel evaporative separator for the same. Looking for the style separator that sits right behind the tank - not the one that is mounted on the middle OEM seat (as early models I believe)...
Looking for some advice / education / direction on how to make any modifications I need to re-route fuel lines as I near the end of reassembly. Looked around and other threads but couldn't find what I was looking for.
Here's the summary for anyone interested.
Bought vehicle a couple of years...
Replaced the master / slave cylinders on my 72' 40 today. The job was partly replacing old / worn parts and part trying to put the right parts in the right places after PO had rigged some things (think hose clamps, etc. ugh).
Elder Statesman hooked me up with the cylinders, brackets, etc...
In the midst of reassembling my 72' after paint and spent the day putting front fenders, bib, grill, hood, etc. on. Running into some trouble with some of the hardware fitting on the hood.
1. The hold spacing for the windshield rests don't seem right. The spacing on these holes is 2 1/8"...
Looking to replace my Weber Carb with an OEM. I've got a 72' 40 with an "upgraded" 2F engine date stamped 12/78. Looking for a stock carb for this engine. Ideally, it'd be re0built and ready to go. But, if I can't find one, I'd be willing to buy a core from someone and have it re-built. If...
Looking for advice on how to bend this floorboard back up to trans hump cover. Re-assembling after paint and now am noticing that somewhere along the way the floorboard end got compressed and now I've got a couple of places where there is a big gap between floor and hump cover. PO originally...
Just upgraded my suspension to OME and pulled off leaf springs, shackles, shocks, etc. Not sure if the suspension is stock or was upsized at some point. Shocks are likely near the end of their life (and not stock) but most of the rest of it is in pretty solid shape. I've still got most all of...
Wondering if anyone can help me with a potential exhaust routing issue....
I'm in the process of restoring my 72' and am going to put the 2" Old Man Emu lift kit on it in a couple of weeks. As I was doing some prior investigating I noticed that the existing exhaust runs real close ( less than...
Anyone know of a good painter to help me finish my project?
Short version of the story - It's not a total body off but pretty close. I've got most of the prep work done (right) and plenty of pictures to show the measures being taken but the guy that's doing the work just doesn't have the...
So, I'm trying to transplant the dash on my 40 that has been butchered (beige one in photos) with an original untouched (green in photos) of the same year (72). The current dash was hacked at with a radio install, holes drilled, etc. and I was originally planning to attempt to weld & modify it...
Looking for a good condition ash tray housing and insert for a 72' 40. I've got the decorative outside plate and pull, so I really just need the two main chromed parts.
PO butchered dashboard with radio cutout and now I'm in search of the following era correct knobs / controls / assembly for my 72' 40 -
Choke control knob
Throttle control knob & cable
Hazard knob & module
Cigarette lighter unit
Vent knob with cable (see previous posting)
Thanks!
Looking to upgrade from my current vent cable pull. Current one is really stiff and has some kinks in the cable that aren't helping.
Used is okay but I'd like to make sure it is fully functioning and cable pulls smoothly. I can cleanup the knob a bit if need be.
See photo of what I'd...
Hey all,
Hope I'm posting this is the right section. Been restoring a 40 and happened to drive by a 60 on the side of the road for sale. Considering buying it with my son and seems like a good chance to get distracted for a while - as if I don't have enough projects. Anyway, interested in...
I'm restoring a 72' 40 that I picked up last fall. I'm a rookie and have decided to strip it down, not quite body-off but darn close, for a quality paint job. So, I'm in the midst of having this thing in a pile of parts in the garage. (See photo of it from midway through the teardown)
What I...
Throwing this out there -
I'm dissembling my truck for a thorough paint job. Not a total frame off but stripping all the weatherstripping, badges, etc. and sanding down to bare metal. Just took off windshield and taking apart, wondering if the 2 defrost panels and knob brackets should come...