I saw this on eBay. Has anyone taken a chance. Mine was removed when i got the car. I bought a manual one to put in the hole in the fender but it would be nice to have it working again, because it's just 90's cool:
https://www.ebay.com/itm/362529271502
Just installed these. Most of mine were missing when I bought the truck. I no middle cover on the driver's side and no middle and rear on the passenger. For $70 with the parts these were great. My goal is too keep as much salt water out of the engine by as possible. I try not to drive it around...
I tried to go down the hagerty route and there were restrictions on needing to have it in a garage, not being able to tow anything and limits on mileage. I was not impressed with the restrictions. I don't have a garage big enough and I do occasionally tow a small trailer.
Yeah i already did that in original orientation. Not realized until i put it back together that the previous owner may have some things crossed. I think i can squeeze my hand up there and move things around
Awesome, thanks!! Very clean. I cleaned mine up the best i could with brushes and some solvent. Does NOT look like that. You could eat off those things.
Does the EGR go into this spout here in the picture, instead of down and around.
Now the question comes how am I going to reroute...
Awesome, thanks!! Very clean. I cleaned mine up the best i could with brushes and some solvent. does NOT look like that. You could eat off those things.
Based on the diagram I'm seeing these potential modifications (red) to bring it in line, but it leaves 1 connection out (Yellow). Does that connection actually lead to the little tip by the grey electrical plug for the EGR temperature sensor, between cylinder 5 and 6 intakes? I always thought...
I think I found my problem. I think I have an extra vacuum switch under the intake from a previous owner.
When I got my car there was a vacuum switch dangling inside the intake. From the picture you can see i have 4 switches, 3 with power and 1 without. On the opposite side of the fuel...
does anyone have a picture for a 97/lx450. One that didn't come with the PAIR system
This post has the diagram: Vacuum line Diagram. - https://forum.ih8mud.com/threads/vacuum-line-diagram.333474/#post-15049915
i have a lx450 and for the life of me i can't find what happened to the electrical connector to 1 of the VSVs underneath the intake. The EGR connector is blue and it's comes from the bundle with the fuel pressure VSV and the 3 connectors for the throttle body. I think the electrical connector...
Yep along with a whole bunch of stuff
Valve cover gasket and spark plug gaskets
Cleaned valve cover, throttle body and upper intake
Replaced PVC valve, grommet and hose
Replaced valve cover breather hose
Replaced little water hoses for throttle body (4)
Replaced vacuum hoses under upper intake...
Thanks for recommending the clamp against the firewall. This is broken on mine and needs replacing. The clamp on the head on the LX450 diagram is actually part number 8271160150 and is available direct from japan, but if it's just a glorified zip-tie I'll just continue to use that. I already...
Reviving an old thread.
Does anybody know the part number of the clamp that holds that harness down (Post #7 red arrow above). Sure I can put a zip tie but figured I would see if I could get the factory wire clamp. I looked in the parts manual but the clamps are really difficult to decipher...
Installed both today and followed your guide on the alternative part Denso 077800-0072. Everything is working as it should. Thanks!
For those of you a little more adventurous. I do see the that you can purchase the transistor inside the heat sink Toshiba 2SD1460. Looks like you would need...
I contacted Wells Electronics the aftermarket park available on rock auto. These are other places to find the exact part
WVE PN 3A1234 RockAuto.com WVE 3A1234 Blower Motor Control Module / Resistor | RockAuto -...
These are other places to find the resistor :
WVE PN 3A1234 RockAuto.com WVE 3A1234 Blower Motor Control Module / Resistor | RockAuto - https://www.rockauto.com/en/parts/wve,3A1234,blower+motor+control+module+/+resistor,6557
WVE PN 3A1234 O'Reilly Auto Parts (special order)
PN RUA1561 Advance /...