Search results for query: *

  • Users: LCSA
  • Order by date

Forum search Google search

  1. LCSA

    Engine rattling noise at light throttle, any ideas

    Sounds like I just need to bite the bullet and just get it done!
  2. LCSA

    Engine rattling noise at light throttle, any ideas

    Yeah, I burn about a quart every 600 miles. 196,000 miles and the head has never been touched to my knowledge (nor the injectors). It’s time for a top end rebuild for sure. I concur, once given more throttle, the noise goes away. Makes me think an injector could be spitting as you...
  3. LCSA

    Engine rattling noise at light throttle, any ideas

    Ever figure this one out? My 93 makes a rattling noise when under very light load/throttle. Higher octane doesn’t help and I’m set at factory spec timing so I hesitate to believe it is pinging… I am beginning to wonder if it’s the timing chain or tensioner that is slightly slack when under very...
  4. LCSA

    For Sale Most recent 200 Series purchase prices

    I saw this one in person. Didn’t notice any irregularities with the repair work but I did not get paint readings. I was able to procure the parts used for the repair work and it appeared to me that the driver quarter panel was replaced. I looked underneath and the frame/IFS looked untouched...
  5. LCSA

    For Sale 1988 FJ62, San Antonio, TX

    Just confirmed with seller it is still available. You can contact him through the Facebook link. Great truck, good luck!
  6. LCSA

    For Sale  1988 FJ62, San Antonio, TX

    Posting for a neighbor of mine who has it listed on FB Marketplace, where you can find his contact info and more pictures. The big selling points of this truck are definitely 1) he is the original owner with receipts for mechanical work and 2) the body/frame/paint. Paint is original and in good...
  7. LCSA

    Stumbling Problem

    Air filter clean and no known cracks. Regarding IAC and TPS, would those cause issue only when not warm? My uninformed logic would make me think those would cause consistent issues despite operating temp?
  8. LCSA

    Stumbling Problem

    Hey Folks, ‘93 with 183k Over the last several thousand miles, I have noticed my truck will stumble when accelerating for the first time after starting the engine (only the first press of the throttle when engine not warm). It will hang up for 3-4 seconds with the throttle pressed and just not...
  9. LCSA

    Low rumble and vibration when letting up on accelerator.

    Speaking for myself, I don’t feel any play in the driveshaft, I did recently grease the u-joints, however a shop did grease the slips and I noticed the sound shortly after. They may have overdressed despite my suggestion of just two pumps.I should probably remove the zerk and just start afresh...
  10. LCSA

    Low rumble and vibration when letting up on accelerator.

    I’m right there with you. I can actually play with the noise a bit by just feathering the throttle when coasting above 40mph or so. It’s that slight pressing/releasing of the throttle at speed that causes the noise (might I add that it’s not overly loud, but I can hear it. I don’t think my wife...
  11. LCSA

    removing TVSS - security system

    Hi Y’all- I know this thread is old but I’m trying to chase down a red wire that was spliced into my park/neutral position switch coming off the transmission. I am wondering if it is the red wire y’all have referenced that goes down the steering column. Any reason TVSS would have an electrical...
  12. LCSA

    Park/Neutral Position Wiring Conundrum

    to add to this, it’s a 93 with a442. No other accessories I am aware of other than alarm, though I am not the original owner. also, some of the wires coming into the connector may be a little loose. I want to shove them in further and ensure they stick. Is there an adhesive glue of sorts suited...
  13. LCSA

    Park/Neutral Position Wiring Conundrum

    Hi folks - my shift indicator lights on the dash have been intermittent for a while now and as a result, I am unable to hold First gear when L is selected (it shifts as if in drive). now I am pretty positive that the issue lies in the 7-pin connector above the starter. When I wiggle it, I can...
  14. LCSA

    Won’t Stay in First Gear

    @Tooth Fairy im curious if you were able to resolve this issue? I’m having the same symptoms. Problem seems intermittent by the day. Did the linkage adjustment work?
  15. LCSA

    New lift new clunk up front.

    Issue solved! As you stated, the shop put the washers on in random order. Thanks for the help!
  16. LCSA

    New lift new clunk up front.

    Iron man gas shocks. Ok my guess is that’s what happened. I will pull them today and realign. I guess it’s surprising to me there’s not a form of bushing designed to go between the hole and the stud but that’s probably also why I’m not an engineer :)
  17. LCSA

    New lift new clunk up front.

    Lubed all zerks yesterday actually. Thanks for the suggestion! I’m pretty positive the challenge is the shock that I can move by over half an inch by hand. I feel like that should not be the case.
  18. LCSA

    New lift new clunk up front.

    To clarify, if feels as if the shock stud is way too small for the bracket hole. Feels as if a sleeve is missing or as if these rubber bushings should have a lip that goes up into the bracket hole but the additional washer is preventing that from happening...
  19. LCSA

    New lift new clunk up front.

    I recently had a shop install the 2” and started hearing the clunk when hitting bumps at speed. Turns out I could move the shock freely with my hands in the shock tower hole and the hole in the bracket on the axle even though the nut on top and bottom were torqued down. I haven’t yet fixed the...
  20. LCSA

    Official LX570s Picture Thread

    One of these things is not like the others...
Back
Top Bottom