Search results for query: *

Forum search Google search

  1. garfieldthecat

    SOLD Seattle Area: FJ60 Stock rear axle 3.7 gearing

    PM sent
  2. garfieldthecat

    For Sale FJ 60 Tan rear seat bottom

    Still available?
  3. garfieldthecat

    Value of non-running FJ62

    Pictures would help. Also, your location. 805? Ventura County CA, maybe? Would be worth more than $1000 in parts alone depending on what parts are on it in good condition. If you want to sell it TODAY, yes you can get $500-$1000 for it.
  4. garfieldthecat

    1987 FJ60 charcoal canister replacement question

    Thanks @CruiserTrash , so the OVCV allows the float bowl to vent into the canister on the same line as the fuel tank with the tee in the tank line. Makes sense. I think the GM canister does have valves on the tank and purge valves. Working with non-oem replacements makes it bit confusing and...
  5. garfieldthecat

    1987 FJ60 charcoal canister replacement question

    Hoping I can get some clarification on the routing for the GM canister. The EVAP page from the emissions manual posted by @OSS shows the tank line as a stand-alone line entering the EVAP canister. It also shows the purge line and the line going to the Outer Vent Control Valve (OVCV) solenoid as...
  6. garfieldthecat

    Builds Woodrow, the 60 - Tilda Bogue Service Station

    I see. I can't replace the downpipe with headers because I am in California, but I will have the welds around the flanges touched up in case they cracked at some point. Thank you!
  7. garfieldthecat

    Builds Woodrow, the 60 - Tilda Bogue Service Station

    Where did the downpipe leak from? The base of the exhaust or the connection to the catalytic converter? Was it because of a crack at one of the flange welds or uneven flange mating surfaces? Thanks for advising. Going to be getting my downpipe ready for a Air/Fuel Ratio Gauge and curious what...
  8. garfieldthecat

    Source for legit Albright contactor in the US?

    Excellent, thank you for the clarification @chbrow10 . I do plan on getting new wiring. I was thinking 2/0 or is it 2AWG? Again, not savvy with motor control.
  9. garfieldthecat

    Source for legit Albright contactor in the US?

    Hi @PIP I am rebuilding an older Warn M8000 winch and want to order the Albright. I had a few questions about the size and wiring requirements. It looks like the space under my plastic cover is 2 1/2" high. Will the Albright fit with the mounting bracket in this space? Also, I have the older 3...
  10. garfieldthecat

    Stock height springs for an FJ60

    These look like they cross-reference to FJ62 part numbers? Are they different lengths than FJ60 springs?
  11. garfieldthecat

    Wanted Denver: FJ60 shifter boot

    This one is listed on PartSouq for 1980s 40s and 55 series, maybe it could fit early 60s? Want to try and let us early 60s owners know? https://www.ebay.com/itm/186026598252?chn=ps&mkevt=1&mkcid=28
  12. garfieldthecat

    Wanted Denver: FJ60 shifter boot

    On SOR's site, the 1980-1982 boot has an inner gasket that looks like it might bolt to the bottom of the boot ring. It might help keep the road noise out. Mine is missing this gasket too. I was going to make one out of this rubber type sheet from Amazon. I think its heat-resistant enough...
  13. garfieldthecat

    Wanted Denver: FJ60 shifter boot

    https://www.gearaid.com/products/aquaseal-repair-adhesive?variant=28044138321
  14. garfieldthecat

    Wanted Denver: FJ60 shifter boot

    Aquaseal might be a good option if you want to save your old boot too. Works great on rubber and neoprene...
  15. garfieldthecat

    Stock height springs for an FJ60

    Thanks for that @Dekeman I'll read back on the thread. And thanks for letting us know that the Dobinson's shackles would be your preference today. Great looking truck!
  16. garfieldthecat

    Stock height springs for an FJ60

    Are the pictures of your truck with the Dobinsons with 5 leafs in front and 6 leafs in rear? Did you notice any height change? If so, how much? What size wheel and tire are pictured? Did you do any axle angle shims? Which springs did your remove from the spring pack? Third one down from longest...
  17. garfieldthecat

    SOLD ISO Early FJ60 rear exhaust pipe bracket

    Looks like a found one on Ebay after all NOS too, score!
  18. garfieldthecat

    SOLD ISO Early FJ60 rear exhaust pipe bracket

    Thank you @Spike Strip . The Ebay one has a different orientation from the one I am looking for and more bolt holes without the welded nut to the bracket. Below are pictures of the one on the truck now. A muffler shop had drilled out one of the holes and the exhaust will likely rattle if the...
  19. garfieldthecat

    SOLD  ISO Early FJ60 rear exhaust pipe bracket

    Looking for an 1980-1984ish FJ60 rear exhaust pipe bracket like the one highlighted in yellow in the picture. Need one that has good threads and hasn't been drilled out for aftermarket exhaust hangers. Thanks for letting me know if you have one available.
  20. garfieldthecat

    How to Guide: Roof Rust Repair by Removing Roof Skin FJ60/62

    Hi @Hokie LX , is the gasket you used the one that could accept the trim back in? I don't see the chrome trim back in the channel. If so, do you happen to have the part number for that windshield gasket? Thanks in advance!
Back
Top Bottom