Search results for query: *

  • Users: A-2-Z
  • Order by date

Forum search Google search

  1. A

    3B Injection Pump won't prime

    Much smoother after a couple laps around the block. Still have a few loose ends to sort but I’m stoked it’s running. Thanks again for the support and information.
  2. A

    For Sale Two 3B’s, parting out or for sale as whole (and other euro 70 series parts)

    Thanks for posting this pic. I am missing this on mine and didn't even know it. I was worried about the stress on the manifold from the exhaust bouncing around, going to make something similar to support it asap.
  3. A

    BJ42 radiator

    I know this is an OLD thread. Wondering is anyone has more updated info on replacement radiator for a 3B with inlet and out let on the Left hand side. Found the below one on Amaz. and was thinking of giving it a try. I don't have a local re-core shop, my original top cap has a pin hole, also...
  4. A

    3B Injection Pump won't prime

    Hopefully it smooths out a bit. It was 35 degrees out, motor was stone-cold and running off a can of old-ish diesel. I haven't even looked at the motor mount situation closely ... or the coolant/radiator.... or the charging system. Felt like I just needed to see some sign of life in the motor...
  5. A

    3B Injection Pump won't prime

    Should be better now.... "sometimes I don't inter-web so good". Thanks for letting me know.
  6. A

    3B Injection Pump won't prime

    It's alive! YouTube short of the fist start. Thanks again for the information and support. So stoked to hear it run, I bought this truck as an incomplete diesel conversion project. Was told the motor ran 10 years ago when pulled from a different Cruiser. Still lots to do but this felt like...
  7. A

    3B Injection Pump won't prime

    Hi. Well after being away from the 3B for the past 2 months, I'm back and just finished tinkering on it> Turns out the rail in the injection pump was stuck in the off position. I determined this by first pulling the observation plate (2X 10mm bolts). This confirmed that when the...
  8. A

    3B Injection Pump won't prime

    Thanks for the above photo. I didn't know that was an injector pump bleed screw, I'll give that a shot first. High tempts today here are well below freezing so will probably wait until tomorrow to get back after this. I really appreciate the information and support.
  9. A

    3B Injection Pump won't prime

    EDIC arm was attached so IF the rack is stuck it would be in the off position. If I'm understanding the way this works then it seems there might still be hope. If the rack is stuck in the closed position then the FCL would still be able to move freely?
  10. A

    3B Injection Pump won't prime

    Here's what I'm working on.
  11. A

    3B Injection Pump won't prime

    I'm not getting fuel, let alone pressurized fuel in the lines leaving the IP. Lots of pressurized fuel at the IP inlet, really feels like the IP is stuck in the "stop" position. I was afraid that the smooth and free movement of that stop/run/rich lever might lean against the stuck rack theory...
  12. A

    3B Injection Pump won't prime

    Thanks for the reply and the links. Truck has been sitting 4-5 yrs, fuel filter was still full of diesel and it looked super clean. I disconnected the tank from the start so only clean new diesel was introduced into the system. I actually found your post about the stuck rack yesterday, super...
  13. A

    3B Injection Pump won't prime

    Filter and lines to the IP are filled with pressurized diesel from hand pump and free of air. I haven't found a fuel bleeder on the IP body, only the oil bleeder.
  14. A

    3B Injection Pump won't prime

    Hi. Looking for some suggestions/advise/help; I've run out of threads to read, ideas and solutions to try. Working on my 40 Series truck that the previous owner started a 3B swap on. (Supposedly the motor came out of a running 60 before the transplant.) I'm struggling to prime the Injection...
  15. A

    For Sale Two 3B’s, parting out or for sale as whole (and other euro 70 series parts)

    Hi, any chance you have a decent 3B oil pan? Thanks
  16. A

    BARELY THERE BRAKES

    Did you end up getting this sorted? My brakes just went "soft" today, pedal almost to the floor in order to stop. Brakes have been fine up until now, no signs of fluid leaks. Sounds similar to what happened to you. Any updates would be great. Thanks
  17. A

    Wanted  BJ40 cast throwout bearing hub and bearing Part #31231-60060

    I'm working on finishing a 40 series, incomplete diesel conversion project I purchased. It has a 3B motor from a BJ60, a steel bellhousing and a BJ40 trans/transfer. The throwout bearing-hub and bearing are missing, I have the narrow cast diesel fork. From the research I have done I believe I...
  18. A

    SOLD 13B-T throwout bearing hub

    Hi, sent you a DM. Do you still have these parts available? Thank you
  19. A

    1993 FZJ80 - Still can't get the P & D lights to work on the dash.

    Old thread but any update? Get it sorted?
  20. A

    Another "Speedometer not working thread"

    Just wanted to share my broken speedo experience. I am in NO WAY an expert, electrician or pinball-wizard, this is just me doing me. Hope it can help others. I just got my first 80 Land Cruiser, a 1994, lower end model, 234k. Amongst numerous issues, the Speedo and OD where not working...
Back
Top Bottom