Search results for query: *

Forum search Google search

  1. OhioFJ

    A question about how to attach the fiberglass top to the windshield.

    You can have some of these larger rivets if you want. I used them to join the visor to the cap. They’re solid aluminum; I used an air hammer and bucking bar to install.
  2. OhioFJ

    2F Carburator to intake manifold stud measurements

    90116-08042 Fit my '79 and still available at the dealer
  3. OhioFJ

    Carburetor base plate vent line routing

    My carb base is like this too on my 10/‘79. The smaller line goes to the lower choke opener on the carb The larger line goes to the Y port on the VCV valve mounted on the driver fender Maybe your setup should be similar? I’m not familiar with difference in the emissions across the years.
  4. OhioFJ

    1st time engine oil change question - 1976 fj40 w/ 2f

    Also consider Magnetic Drain/Fill plugs 90341-18021 for the transfer case and front/ rear diff Steel crush washers 12157-10010
  5. OhioFJ

    Dobinsons lift - HELP

    I had the exact same problem. They are not made correctly. I used other pins instead and sent these back.
  6. OhioFJ

    1st time engine oil change question - 1976 fj40 w/ 2f

    Yes that's it What happened to your clutch inspection cover?
  7. OhioFJ

    Builds 1978 US Market FJ40 Factory Restoration

    That’s chestcutter’s truck, I just remembered that he wrote about sourcing that part. Maybe toyotamatt would have that orange line?
  8. OhioFJ

    Builds 1978 US Market FJ40 Factory Restoration

    Check this out, might help. Post in thread 'Ohio Red 1978 FJ40' Ohio Red 1978 FJ40 - https://forum.ih8mud.com/threads/ohio-red-1978-fj40.1245224/post-13863237
  9. OhioFJ

    Dobinsons rear leaf spring install

  10. OhioFJ

    Dobinsons rear leaf spring install

    I redrilled the perch hangers to center the rear axle.
  11. OhioFJ

    10/'79 FJ40

    Yes and that’s where I got it from.
  12. OhioFJ

    10/'79 FJ40

    With everything flat it was time to remount. I read a ton of threads about which gasket to use - in the end I used a felpro. The biggest hassle in getting the thing back together was having to loosen and reattach the EGR cooler, J pipe, and exhaust. The new carb heat shield is slightly...
  13. OhioFJ

    10/'79 FJ40

    I wanted to have my manifold machined however the rotating horns complicated things. To keep everything together as a unit, I first loosely bolted the intake and exhaust manifolds together with the appropriate gaskets and block off plate, then mounted this back to the head without an exhaust...
  14. OhioFJ

    Canton Cars and Coffee

    I can’t make it - have to work 💩
  15. OhioFJ

    Best manifold gasket?

    Are the torque specs for the felpro gasket the same as those listed in the FSM (28-37 ft-lbs)?
  16. OhioFJ

    10/'79 FJ40

    I modified a manifold insulator plate to fit the emissions ports on my manifold. New leather carb accelerator pump plunger and boot installed, along with a new fuel cutoff solenoid. I noticed some fuel residue on the old insulator plate and around part of the carb - I assume it was fuel from...
  17. OhioFJ

    Unofficial Ohio Cruiser parts FS/WTB/trade thread

    I'm trying for a light lager. Modelo or something like that. Seems like it should be simple but pretty exacting really!
  18. OhioFJ

    Unofficial Ohio Cruiser parts FS/WTB/trade thread

    @Brew40 Could use your help here!
  19. OhioFJ

    Unofficial Ohio Cruiser parts FS/WTB/trade thread

    I really don’t know - they look like Toyota seats but they aren’t original to the vehicle.
  20. OhioFJ

    10/'79 FJ40

    Tack them so they can’t rotate while being refaced. I’ll grind out the tack after
Back
Top Bottom