Search results for query: *

Forum search Google search

  1. F

    Carb Woes

    Any suggestions, if I have removed them. Can I re-stake them some how?
  2. F

    Carb Woes

    I think I may have really done it now. I am attempting to rebuild my carb. When I disassembled to clean, I got carried away and removed the paddles. Which now I have a big concern for me with those little bass screws. I am sure were meant to be removed. Do I have to worry about them...
  3. F

    Throttle bracket on Carb

    Here is a real left-hand turn, but what is the best option for converting over to EFI on a stock 155F? I see a lot of threads dealing with 2F engines. Besides the cost, there doesn't seem to be any reason not to convert. Jerry
  4. F

    Throttle bracket on Carb

    I thought it was more of a plug and play. I think I am going to scrap the idea and rebuild my original carb. Thanks for all help. Any suggestions on a good rebuild kit?
  5. F

    Throttle bracket on Carb

    Yes, I do. My problem is bracket does fit around the casing and the diaphragm mechanism gets in the way.
  6. F

    Throttle bracket on Carb

    I will check that out. Without modifying the bracket, I can't get it to fit using the base screws. I tried mounting using that screw in the middle but it binds just enough.
  7. F

    Throttle bracket on Carb

    This is the throttle system that I have. I tried rigging it up, but it tends to bind a bit.the bracket doesn't quite fit where it should.
  8. F

    Throttle bracket on Carb

    I purchased a cheap Chinese Carb for my '73 FJ, but my throttle linkage does not fit properly. Does anyone know where I can get a throttle bracket similar to this one?
  9. F

    Chinese Carb w/no fuel return

    I have a pre-9/73 FJ40 with an F155 engine. I decided to give the Amazon carb a shot. My question is, can I add a fuel return by threading and drilling out this port? Is a return line necessary?
  10. F

    External Ignition Resistors Smoke

    First, I have a pre-9/73 FJ40 with the original F155 engine. The wire I plugged into the new starter is Black w/ YELLOW tracer. The unused wire is also black w/ YELLOW tracer but has an inline connector and is a smaller grade wire than the one I plugged into the new starter. Here are some...
  11. F

    External Ignition Resistors Smoke

    Here are the pictures of the ignition coil/ resistor and the new starter. Any help would be much appreciated.
  12. F

    External Ignition Resistors Smoke

    The starter that I installed was .. Toyota 28100-60070-84 I believe it is the gear reduction starter from the FJ60. I will send pictures tonight. Jerry
  13. F

    External Ignition Resistors Smoke

    I will send a picture when I get home tomorrow. When I wired the new starter, I did not change anything. In fact, there was one wire I didn't use that was on the old starter. This is more than likely the problem.
  14. F

    External Ignition Resistors Smoke

  15. F

    External Ignition Resistors Smoke

    I am getting smoke out of the external Ignition Resistor when the key is in the on position. I had disconnected the wires to clean up the fender and install the upgraded starter. All the wire looks as it was before but now after a minute with the key in the on position, the resistor starts to...
  16. F

    PTO Winch Seals/bearings

    I need to rebuild the front bearing carrier on my PTO Winch '73. Does anyone know where a guy can get the seal, bearing, ect?
  17. F

    Preserve for Restro

    I am wondering if there is a go-to for preserving metal (Frame, Engine, and Body) while waiting for the time and money to do a frame off. I am currently replacing the radiator (Ha, Ha) and have progressed to taking off all the front body panels on the FJ40. With access to the engine bay and...
  18. F

    Radiator Replacement and Growing

    Using muriatic acid, do I have to worry about the seals? Jerry
  19. F

    Radiator Replacement and Growing

    When I opened the drain block it was crudded up pretty bad. Took a while to break through. The old radiator had some previous damage (looks like the fan blade must have broken off at some point). I wonder if the PO dumped some radiator stop leak in there. Anyways I was thinking of running...
  20. F

    Radiator Replacement and Growing

    Do you guys add a fan clutch to older models? If so, is this something a guy should look at? The list keeps growing! Jerry
Back
Top Bottom