Search results for query: *

Forum search Google search

  1. SPRDAV

    Hi I'm Superdave

    Well I need to get back into my land cruiser. It has been sitting in the garage for far to long. I was the president of Cascade Cruisers in 2004 or 3 not sure which. We are going to try and get the Cruiser ship shape for Cruisin The Woods. Hope to see you all there.
  2. SPRDAV

    For Sale  2008 FJ40 Rock Buggy

    2008 Rock Buggy: RAM JET 350 Multi-port Fuel Injection, TH350 Trans w/ B&M Holeshot torque converter and Manual Valve Body, ATLAS 4 speed transfer case, Drivetech Drivelines w/ front carrier bearing; Dana 60 front (shortened), PSC full hydro steering, 14 Bolt rear shaved 2", both Detroit...
  3. SPRDAV

    Ram Jet 350 to H55 install-73 FJ40

    I put the same motor in my rock buggy, but have yet to hook it up. I'm going to refer to this thread later. Thanks for the good info.
  4. SPRDAV

    Builds ROTW: CreeperSleeper

    Federal government must take its cut, then I can finish Oocums Razor.
  5. SPRDAV

    Builds ROTW: CreeperSleeper

    I will never forget after my attempt at Duane's mud pit with my 40, your attempt at the mud pit with your 80. Listening to your motor bounce off the rev limiter sounds like victory...............
  6. SPRDAV

    Coilovers, which one???

    Ya, I might be interested, I was leaning towards 18" in back and 16" up front though. I'll keep ya in mind. I'm making a run to Metaltech tomorrow for link parts. SD
  7. SPRDAV

    Coilovers, which one???

    Eskimo, ya there was some head scratching when it came to the hood. I still need to split the corners, dolly the it up to meet the mid section and refab, but it was enough to fab the front top main tube. LT, I did not know you are a SAW dealer, good to know. Let me know when my...
  8. SPRDAV

    Coilovers, which one???

    Well I'm about half way thru my construction of my rock buggy, and I need to make a decision on coilovers. Fox, Sway-away, or ?? Anyone with customer service issues? If I need to swap out a coil for a different rate, will they do it free?? BTW Mark (Metaltech), I'm going to use your...
  9. SPRDAV

    Dana 60 front axle question

    Make sure it's not a D44 closed knuckle.
  10. SPRDAV

    Starter clicks, engine fires then dies, starter still clicking...

    I have a '70 and found the problem during a rebuild. Two of the three wires, about 6" from the ignition switch had melted together inside the wiring loom. Not sure if this helps...............my 2 pesos
  11. SPRDAV

    Beadlocks, Beadlocks, Beadlocks...

    I was leaning towards a standard black wheel and interior inflateable beadlocks. Locks both sides of the wheel. Not sure on prices or availability, I haven't done much research yet.
  12. SPRDAV

    Caster angle, or trail?

    From my understanding, the bigger tire the more caster? Someone correct me if I'm wrong. I've heard of 5-7 degrees for 40-44" tires. I have 35's with 1 degree, works great. If you want to increase caster you will need to cut and turn the knuckles.
  13. SPRDAV

    V8 conversion help??

    AA sells a bracket for the LC Slave to Chevy bellhousing. Take a look at that one and see if it matches what the PO put on? You might just need to adjust the slave push rod? My problem was really similar with the NV I had. I replaced the flexline from the master to the slave because the...
  14. SPRDAV

    Which Tranny? Turbo 350, 4spd, other?

    I gota agree with all of the above because of experience. I had a NV4500 and changed over to an auto. More fun to drive and better control on the trail. Honestly I didn't see a huge mileage difference. Never really calc it, to depressing.
  15. SPRDAV

    crawler options...

    My vote is for the lower geared 465. You can always shift out (shift to high) the 203 if you need a higher gear. Plus, with any stick you have a larger range of gear ratios. I say go low, if you don't like it, don't shift it (or shift it to a higher gear). With my set up I would like a...
  16. SPRDAV

    nv4500 conversion

    I used the chevy version too, but used AA's bell housing to reuse the stock FJ40 slave cylinder. Everything brand new from the flywheel back to the adaptor I think I was 2900$ ??? I sold it about a year later for an auto tranny setup. Look below. Ended up with 1K in my pocket too.
  17. SPRDAV

    Volvo C303 Portals

    http://www.killeraxles.com/html/used_unimog_axles.html
  18. SPRDAV

    let's see yer cruiser

    my junk
  19. SPRDAV

    Warn XCL link issue

    This is the first I've heard of any malfunction with the Warn set up. Maybe that's why they discontinued Black Diamond by Warn??? Glad to hear your OK Gary. Do you have pics from my RTI????
  20. SPRDAV

    let's see yer cruiser

    Hey Gary, do you have the pics of your cruiser and mine on the RTI??? Superdave
Back
Top Bottom