Search results for query: *

  • Users: RobW0
  • Order by date

Forum search Google search

  1. RobW0

    Dissent rear bumper lights issue

    Did you order the light from Dissent when you ordered the bumper? My instructions say the blanks are replaced with the brackets if you order the combo lights.
  2. RobW0

    Dissent rear bumper lights issue

    My Dissent bumper had mounting brackets for the lights.
  3. RobW0

    Cruise Moab roll call

    I thought from your first post you were towing your LC on a trailer, not carrying your 37" tires in the trailer.
  4. RobW0

    Cruise Moab roll call

    Brakes are fixed and I will now be able to leave for Moab on Sunday without delay. Todd at Napelton's Toyota in Urbana, IL did a fast turnaround on getting the parts for my 200. Will be in Moab some time on Tuesday.
  5. RobW0

    Cruise Moab roll call

    Just discovered a problem with my front driver brake caliper and rotor. At the dealership now. Hoping I can get it fixed tomorrow. Was planing on leaving for Moab on Sunday. Fingers crossed I don't get delayed.
  6. RobW0

    Panhard drop bracket option?

    Basically the more level the panhard is the smaller the difference will be. This is from their website: " SHORTY OPTION: HOW DO YOU KNOW IF YOU WANT/need A SHORTY. On a flat surface Measure from the ground up to the center of the bolt on the frame side. Then do the same thing on the axle...
  7. RobW0

    Panhard drop bracket option?

    I found an explanation under one of the other kits on the site. Talks about the the difference in height between the upper bolt on the driver side and the lower bolt on the passenger side.
  8. RobW0

    Tire Pressure recommendation

    thank you for the confirmation.
  9. RobW0

    Tire Pressure recommendation

    Falken Wildpeak R/T01 285/75R17 C1 load on 2019 LC200. @gaijin if I used the calculator I have the RCTIP as 37 to 38psi. Am I in the right range?
  10. RobW0

    Panhard drop bracket option?

    Mine got delivered today. Looks like the weather will be good on Monday, so will try to do the install then.
  11. RobW0

    KDSS Relocation Question.

    Thanks for the response. I ordered some parts today based on your KDSS relocation thead. Not sure if I will get it all in before Cruise Moab, so may have to wait until after that. Only rubs at full lock to one side right now.
  12. RobW0

    KDSS Relocation Question.

    I just went to 34" tires so I have rubbing on the KDSS arm. I need to do the KDSS relocation, so is the sway bar lowered and moved forward a little bit with the relocation kit? The am asking because I am wondering if I will need to make some modifications to my budbuilt front skid? Also does...
  13. RobW0

    RedArc BCDC help

    There should be some fuses between the start battery and the BCDC, have you checked them to make sure they are good?
  14. RobW0

    Cruise Moab roll call

    I have done the Hells run the last few years on Thursday with Matt. Hope to be able to do it again this year. Wife is coming this year for the first time so the other runs will be some mild scenic runs. Had to cancel at the last minute last year so looking forward to this year.
  15. RobW0

    USB conversion

    Assuming the rear part of the console is the same as a 2019, it is just a matter of using your pry tools on the seams of that bottom rear piece until it pops off. I don't remember the exact spot as I did it about 5 years ago.
  16. RobW0

    Ham radio mounting locations

    Something to think about for the power, is putting it on a relay. I have a fuse block in the back of the truck and the power for the base unit wired with a relay so it turns on and off with the truck. I also have it set up so I can trigger it on with my ARB LINX system when the truck is off. I...
  17. RobW0

    New-ish Falken Wildpeak R/T 01

    Thanks for the update. It has been mild, a little, south of you also other than some ice last month. Still undecided between C and E.
  18. RobW0

    New-ish Falken Wildpeak R/T 01

    I am thinking about getting a set of these to replace my K02s. How is everyone liking them? Was looking at the 285/75/17. I have the E load K02s so was unsure if I want to get the E in these or go with the C load rating.
  19. RobW0

    Rear Camera relocation kits?

    This is the last thing I still need to do for my Dissent rear bumper. Interested to see how everyone is doing it. The Kaymar harness sounds interesting. Might do something with my front camera also. Would need to make some kind of new housing for it however.
  20. RobW0

    Dissent Rear Bumper Question

    So it is not the bumper but the tire carrier that has the problem. You might want to update your title.
Back
Top Bottom