SOLD
For Sale:
1978 Toyota Landcruiser FJ55 with Factory A/C
- Factory Working A/C (needs charge)
o Compressor spins freely when switched on.
- All electrical works
- Rear tailgate operates both by key and dash switch
- Cruiser drives straight
- Engine starts and pulls hard...
SOLD
For Sale:
1978 Toyota Landcruiser FJ55 with Factory A/C
- Factory Working A/C (needs charge)
o Compressor spins freely when switched on.
- All electrical works
- Rear tailgate operates both by key and dash switch
- Cruiser drives straight
- Engine starts and pulls hard...
For Sale: All New never used
-intake/exhaust manifold gasket
-two REM heat riser gaskets
-nonusa insulator
-set of manfold stud kit
SOR part numbers/descriptions below:
044-01b/c-rem: Graphite Manifold Gasket - SOR Price: $35.18
Fits 1/75-8/87 - Remflex Graphite gaskets are made...
For Sale: New from SOR Aftermarket Rear Brake Shoes - Fits 1961-7/80 (4 shoes = 1 axle).
New never used/installed. New ones are $40 plus shipping, plus handling
Price $35 shipped to your garage
For Sale: Used FJ55 Tailgate Window Rubber removed from FJ55.
The rubber is still soft. one part has worn away yet still does not allow sound/air in. Can be glued into place for many more years of enjoyment on you pig.
Questions Ask!
SOLD
2nd photo shows the location of the wear.
I purchased a set of rear cargo seals from slocruisers and ended up not needing them. These are new, un-used, not even out of plastic wrapping.
Link to Slocruiser site: http://www.slocruisers.com/product.sc?productId=20&categoryId=11
SOLD
For Sale is a Weber 2F Carb.
Carb # 11046
Carb made in Spain.
Includes all necessary linkage to install and replace your mechanical linkage and go with the cable setup.
Includes used air filter.
Condition: Carb needs to be tuned. My 55 ran rich but started every time.
Price...
For Sale is a used Aisan Carb that was removed from a 1978 FJ55 2F.
I ended up not rebuilding and going with a trollhole instead.
Carb Number: Aisan 21100-61024
Questions just ask.
Price: $150 oBo Shipped to your garage!
I am looking for a lower throttle linkage where the lower throttle pivot comes out of the firewall into the engine compartment and then goes up to the upper pivot.
I need the long linkage between the two pivots. I thought I pulled everything I would need to get it back to stock however I...
Ok while not the season to sell watercraft it is here in Florida! Its 76 and not a cloud in the ski. Also not sure if this is the correct section.
Mud Notes: Willing to trade for cruisers, boats, RV's etc... If it is fun than I may be game!
For Sale:
Pair of Wave runners in...
WTB hard front DS brake line that mounts on the axle from the "T" coupler and carries fluid to the flex lines. It runs across the front axle.
Years 9/75-1980 will work.
need part #43 depicted in photo.
WTB hard front DS brake line that mounts on the axle from the "T" coupler and carries fluid to the flex lines. It runs across the front axle.
Years 9/75-1980 will work.
FJ55
need part #43 depicted in photo.
I am converting my FJ55 from a weber back to a Trollhole carb.
I'm in need of the hard fuel line that attaches to the carb to feed the fuel. Mine was converted to a soft line and need the one that threads into the fuel inlet.
Believe 2F 1/75-4/79 will work.
Let me know what you...
I am converting my FJ55 from a weber back to a Trollhole carb.
I'm in need of the hard fuel line that attaches to the carb to feed the fuel. Mine was converted to a soft line and need the one that threads into the fuel inlet.
Believe 2F 1/75-4/79 will work.
Let me know what you have...
Ok I've searched and have a weird one going on.
Rebuilt front axle, re-used old bearings (perfect condition).
Repacked with hitemp wheel bearing grease
torqued to hubs to spec 45 turned every which way then back off to 10 lbs
drove and had tons of heat. could not keep hands on hubs...
I am looking for a Parking Brake handle Assembly (bracket, pull handle, claw, and other bits to mount on the interior. Mine is destroyed beyond belief.
cable is optional and desired but not critical.
Let me know what you have. Only criteria is that the claw holds the pull handle other than...
NEW SOR Front Wheel Bearing Kit - 75-90 KOYO
I just finished the front of my piggy and did not replace the bearings. Mine looked great!!
Purchased these from SOR and did not use.
Fits 9/75-1/90-Comes with inner & outer wheel bearings, wheel seals, lock tabs, & hub gaskets-Does both...
WTB: Metal Knuckle housing ring seal
So yes I am doing the front axle rebuild from hell... Done many of these however my cruiser karma is not with me now. I threw away my inner metal ring that is depicted in the photo below.
Anyone have two of these your willing to part with please let...
So yes I am doing the front axle rebuild from hell... Done many of these however my cruiser karma is not with me now. I threw away my inner metal ring that is depicted in the photo below.
Anyone have two of these your willing to part with please let me know.
Believe any disc brake...