Search results for query: *

  • Users: EricG
  • Order by date

Forum search Google search

  1. EricG

    Pinion Seal Adventure - Bad Superseded Part

    Ok, I guess I didn't read far enough - didn't see that section. Thanks, I'll take a look at it. Maybe I'll be re-doing this job :bang: I had to lean hard on a big ratchet to get close to the turns, but I doubt it was anywhere close to 181 ft pounds.
  2. EricG

    Pinion Seal Adventure - Bad Superseded Part

    I used the OEM washer with the 90179-22005 part. Where do you get the "181" torque number from? FSM (pg SA-80) has a process for setting bearing pre-load, but as far as I can tell, the 3rd member has to be removed to do it. I counted the turns taking the original nut off, and put the new one...
  3. EricG

    Pinion Seal Adventure - Bad Superseded Part

    I looked at that - it would still be to tall.
  4. EricG

    Help with leak near rear diff

    Yes But see the thread I just posted (Pinion Seal Adventure - Bad Superseded Part - https://forum.ih8mud.com/threads/pinion-seal-adventure-bad-superseded-part.1329519/). The pinion nut they'll try to sell you (90179-22016) is wrong and won't work. Part 90179-22005 is a workable replacement.
  5. EricG

    Pinion Seal Adventure - Bad Superseded Part

    The other day, when I went to replace my rear brake pads, I found oil *everywhere* under the back of the truck. Complete mess. Seems to be the pinion seal. I dumped a quart of gear oil into the diff and it didn't fill it. I just got back from about a 3000 mile road trip in the truck. No...
    • EricG
    • Thread
    • diff oil gear oil pinion rear brake pads seal
    • Replies: 9
    • Forum: 80-Series Tech
  6. EricG

    Christmas Tree Cutting Support 2023

    Right, but according to recreation.gov, the end date is this Sunday. But only for Pikes Peak - the other 4 ranger districts are open until the 31st
  7. EricG

    Christmas Tree Cutting Support 2023

    Hi - general Christmas tree permit question. The odds have been against me this year, and I haven't made it up with the club yet and haven't gotten our own tree either. And I won't be able to get there this weekend. The recreation.gov site shows permits are good through 12/31 everywhere...
  8. EricG

    Colorado Land Cruisers Christmas Party December 12

    I'll be there, no guest
  9. EricG

    Christmas Tree Cutting Day 5 Saturday December 9

    Hope you guys had a good day up there. Really wanted to make it. Here's my latch mechanism. The red line shows the part that broke off. There's supposed to be a spring in that channel that causes the latch to engage when you close the door. Luckily I had one in my parts stash, because it's...
  10. EricG

    Christmas Tree Cutting Day 5 Saturday December 9

    Door latch is FUBAR, need to replace. Not gonna be up today 😕
  11. EricG

    Christmas Tree Cutting Day 5 Saturday December 9

    Hey guys, one of my doors won't latch this morning. Working on it, but will likely be late at best.
  12. EricG

    Christmas Tree Cutting Day 5 Saturday December 9

    I'm seeing 7" to 11" on weather.gov Snow day guys! :bounce2::bounce2:
  13. EricG

    Christmas Tree Cutting Day 5 Saturday December 9

    Ok, going to try to make this one!
  14. EricG

    Christmas Tree Cutting Day 4 Sunday December 3

    Hey guys, something has come up and I'm sot going to make it tomorrow. Sorry :(
  15. EricG

    Christmas Tree Cutting Day 4 Sunday December 3

    I'll be up on Sunday
  16. EricG

    Canyonlands, Springs Break 2024

    Hi folks, The Spring reservations for Canyonlands opened this morning and I got 3 nights on the White Rim trail March 26,27,28. Sites are for a max of 3 vehicles/15 people. Probably depart on the 25th and camp somewhere between Rifle & Moab, and return on the 29th or 30th. Haven't figured all...
  17. EricG

    Slow Motion LS Swap - (aka Heater/Cooling System Issue)

    So I took the truck in for a Dyno tune today. The guys at Under Pressure Power and Performance hooked me up on their AWD unit. Did a baseline pull to see where things were, and then cleaned it up a bit. My main concerns were getting rid of my persistent P0300 code (random, multi-cylinder...
  18. EricG

    October Alternate Trail Ride, Sunday 10/29/23 Trails off of Old Stage Road

    Nov 5th https://www.timeanddate.com/time/change/usa
  19. EricG

    For Sale / Wanted Thread

  20. EricG

    New US Land Cruiser

    I doubt you'll see any passenger cars with diesel going forward. I'm happy to see the price point come down - article I read said the base model was in the neighborhood of $55K. Which is still a lot of money, but a big step in the right direction compared to the 200 series approaching $100K -...
Back
Top Bottom