Search results for query: *

  • Users: yomama
  • Content: Threads
  • Order by date

Forum search Google search

  1. Y

    Try and answer this one ALT meter ?

    I thought of an interesting question :D The alt guage on the dash, does it tell you the condition of the battery OR does it show the charging state? Does that make sense? If your battery is low would the alt meter show high (charging) or low (battery dying)? I am still working on my...
  2. Y

    How many amp draw? and?

    I have three questions I could use a little input on. Oh yea, I did "search" and I can't even remember what I used as key words and the next thread I find is "Who shaves their nuts". I read the first page laughing my ass off. I will return tomorrow to read that and hopefully get some input on...
  3. Y

    Here is an aftermarket ECU

    I am in the process of making some changes (Possibly removing my UNIchip) and adding some things to basically do what the unichip is supposed to do, but won't let the average joe tweak without the proper equip. Anyhow I was searching on the net and found this website www.ecudirect.com I think...
  4. Y

    Where or Where has CruiserDan

    Gone off to? I sent him a PM a couple days ago and haven't heard from him. I also have not seen any posts from him in a few days? Yomama
  5. Y

    Body lift?

    What are everyones thoughts on a body lift? I already have the OME springs. The only reasons I am looking at this is a little extra tire clearence never hurts, but also if I replace my replaced exhaust, this time I would like to go 3" all the way to the back, not just to that pinch locaation...
  6. Y

    Gauge Pods

    Cage? You have a roll bar in your LC? Interesting. That looks like a good place for guages, not sure if I would want to remove my anniversary badge though.... Yomama
  7. Y

    Antenna WIRE for radio

    I searched here, I searched there (FSM and Electric FSM) and I do not see any discription of how to replace the antenna wire. I don't have the original antenna, I replaced it when I had the cruiser tore down to the floor, so then it was easy. Now years later I need to feed a new line through...
  8. Y

    Ok, I am tired of using the "Search"

    Apparently I cannot come up with the correct words in the "Search" to find how much and what type of fluid goes in the center diff. I picked up 4 quart's of Amsoil 75-90. I intended to do the front and rear diffs, but after thinking about it, I have done those twice and have not done the...
  9. Y

    I enjoyed getting my

    It was that time of the year to get my oil changed. I used to do it myself, but with the hassle of storing the oil in a drum and taking it to get disposed I have broken down to let the Valvoline guys change my oil. It had been a year since I was in there since I am running Amsoil and had less...
  10. Y

    Why you should label wires...

    The weekend before last when I did my (still weak) horn upgrade I needed to tap into some 12v ignition switched power. Looking at my handy electrical book for the 80 I find the center diff relay in the drivers kick panel. 30 Amp will be fine to tap into and I really doubt that I would ever...
  11. Y

    Radiator Specs 1997 LC with Air/Trans

    I was wondering if anybody had the specs (good ones) or maybe has a bad one they could send me ::) In my never ending quest to keep the engine/compartment cooler I am considering having a completely aluminum radiator custom built to the original specs + if there is room for improvement. Along...
  12. Y

    ARB Stainless Steel airlines

    Don't know if any of you have run across this. I had to replace one of my airlines (rear) as I ran the :ban: thing too close to the exhaust. Actually it wasn't a problem until I added the turbo, then the extra heat on the front heat shield didn't protect the plastic line anymore. Searching...
  13. Y

    I don't mean to honk my own horn but,

    All the hundreds of posts on this forum and nobody has mentioned (that I recall Junk :slap:) that fact that the weakest component on the LC is the horn :'(. Seriously I drove by my neighbors house and tooted my horn, then hung my head in shame. Is that my horn ??? sounds like a compact...
  14. Y

    Lights for ARB bullbar

    Hey all, The el cheapo lights I originally installed in my bullbar suck. Time for new ones. Here is what I am looking at http://www.4wheelsupply.com/cat.cgi?s=JOIC&c=L. Question is, will 6" lights fit on the ARB without some kind of modifications? Also, does anyone know where to get...
  15. Y

    All this tire talk got me to thinking.

    Since one can not have the best of both worlds without doing a tire swap from on/off road use and none of the tires are great at all things, What if you ran AT's in the front and MT's in the rear (as long as they are the same size) like BFG AT's in front and BFG MT's in the rear. Granted you...
  16. Y

    Stainless steel brake lines

    Who out there in the US has put on the SS brake lines? Just wondering if it is the same procedure that George wrote up. I recall he had to get some washers and he mentions filing part of the connector? That bothers me a little. Any other tips? My speed bleeders just arrived so now I can...
  17. Y

    Don't ever buy parts from

    A place in Ozark, MO called Las Brisas Sales. The person apparently doing the book work is the rudest person I have met. I ordered two used parts from them, one was correct the second was the wrong part and it arrived damaged. I said I would like to return it and get a refund. Well it took...
  18. Y

    C-Dan Air conditioning question?

    Ok, We are hitting the 80's around here now and since I have my A/C back together it is time to filler up. C-Dan, I called local Pepboys and was quoted $150. I am pretty sure I have seen the "Do It Yourself" cans with a connector. It used to be pretty easy. Can you offer any instructions and...
  19. Y

    Anyone ever have a problem after washing motor?

    Hi all, Last Thursday while I was washing the outside of the truck I popped the hood and noticed the usual dust and dirt. The vehicle had sat at least an hour before I had hosed the engine off. Let it sit about another hour after words to dry. Started it up, drove it in the garage, next day...
  20. Y

    MTS Have you installed those Speed Bleeders Yet?

    MTS, Wondering if you installed those yet and if you had any problems? C-dan says the front and rears are different part numbers. Thanks, Yomama
Back
Top Bottom