Search results for query: *

Forum search Google search

  1. CorporalClegg

    What have you done to your 100 Series this week?

    Yeah those don't come around too often.. IFS on 285/75/18's Took the cruiser over Hancock, tincup and Cumberland pass over the weekend
  2. CorporalClegg

    The MUD 100 series Photos thread

    Crusin USA
  3. CorporalClegg

    What have you done to your 100 Series this week?

    I think I have a problem third car in a month
  4. CorporalClegg

    What have you done to your 100 Series this week?

    This for the 98, 99 also?
  5. CorporalClegg

    What have you done to your 100 Series this week?

    Exceeded the towing capacity.. I really need a brake controller.
  6. CorporalClegg

    The MUD 100 series Photos thread

    I hate mud.
  7. CorporalClegg

    New to me

    Recently picked up a non running 3rd gen. Bought this to sell but I don't know that I'll be able to let it go now that it's running. Limited model with functioning locker complete with a cheap respray. This thing jumped time, has a new NTN tensioner, mitsuboshi belt and koyo idler bearings...
  8. CorporalClegg

    The MUD 100 series Photos thread

    About all its worth at 5000' Found a non-running runner, may have to say goodbyes to the cruiser..
  9. CorporalClegg

    New yukon pinion crushed (not the crush sleeve kind of crushed)

    Looks like they used a puller on the yoke/ flange and then commenced to beating the crap out of the pinion with a hammer to get the pinion out of the carrier. Yes you can replace just the pinion gear, sure but you will get noise no matter how it's set up, if this is a high mileage car most of...
  10. CorporalClegg

    The MUD 100 series Photos thread

    Cruiser patiently waiting for house projects to come to a stop for some mountian adventures. It's been a good sport about doing daily duty during hail season and not getting an awning or fridge because of other expenses..
  11. CorporalClegg

    Poor life decisions epitomized; Taking Mom's car to the party

    Little late to the party here but... I must say this has crossed my mind more than once, a ls430 I had showed me what great engines these are. Albeit this m273 TT engine I have laying around gives me ideas for a G wagon t cased and 7 speed auto 100, if only 2ur's were affordable.
  12. CorporalClegg

    What have you done to your 100 Series this week?

    Yep, pretty bad maybe if they cost 100 I would buy again.
  13. CorporalClegg

    What have you done to your 100 Series this week?

    Made my cruiser jealous by bringing home a new toy..
  14. CorporalClegg

    What have you done to your 100 Series this week?

    Fix my mistake as a direct result of procrastination.🙄 Front differential bearings with 15k miles on them. Long story short my ARB lockers had bad bonded piston seals and the axle seals did not survive the second time around. The very slow leak that I was topping off all the sudden one day...
  15. CorporalClegg

    How to know if PO tanked the charcoal canister

    You need to check the canister vent valve, it is what allows the tank to breath through the canister to atmosphere. If it's stuck closed you'll not be able to fuel up the vehicle. If you're wondering if the canister has been fuel soaked the best way is to monitor fuel trims or o2 sensor for...
  16. CorporalClegg

    The MUD 100 series Photos thread

    Installed garage alpha grill over the weekend, what a horrendous pile of crap..
  17. CorporalClegg

    What have you done to your 100 Series this week?

    Stripped the roof clean for some house work..
  18. CorporalClegg

    What have you done to your 100 Series this week?

    It's in the door jamb where the bending occurs when door is opened. Pull the kick panel and driver dead pedal unplug the connectors 4 on my 99 lx, remove driver door panel and speaker, pull the harness through open the taped loom and find your culprit.
  19. CorporalClegg

    What have you done to your 100 Series this week?

    After 2 years of dealing with driver door speaker cutting out when the door was open I decided to do something about it. A little solder fixed it up. Wish more manufacturers made door harnesses this easy to remove/ repair..
  20. CorporalClegg

    Accelerator pedal position sensor - P2121

    If the code didn't return you have an intermittent problem. TIS does have a check mode function, this will change the code set criteria to set the DTC at first failure under a reduced amount of time. I don't know the extract criteria for a 2121 but it's a pretty simple fault to diagnose. what...
Back
Top Bottom