Search results for query: *

Forum search Google search

  1. Cody Quesnelle

    Windshield wiper motor ground?

    1976 fj40 2f So took a couple days off looking for my vacuum ghost....so today windshield Wipers My wiper motor works good until I mount it to the frame.then only one slow speed and switch has no affect.is the wiper motor supposed to be grounded at its mount?any ideas 😬 cause I’m fresh out lol.
  2. Cody Quesnelle

    Aisan carb shaft bushing....

    Rebuilding my carb and feeling strange not replacing the shaft bushings.anybody know the bushing size,or a source to buy them .....or are they“unobtanium”lol
  3. Cody Quesnelle

    Carb vacuum leak!rebuild?or buy new?

    So I had an issue with my idle adjustment screw not changing idle,no change full in/only stalls when you fully remove it.did vacuum test pumped air through booster and found some bubbles I assume this ain’t normal.(doesn’t Change idle when sprayed with carb cleaner that’s confusing lol)so...
  4. Cody Quesnelle

    Idle mixture screw does nothing 🤔

    Trying to tune my carb 1976 2f Asin carb, idle mixture screw does nothing?any body have any ideas what is up,
  5. Cody Quesnelle

    To plug or not to plug?

    should these ports be plugged?
  6. Cody Quesnelle

    Help me please 😬...lol carb/timing problems

    Hey all ...struggling with carb tune and engine timing,1976 fj40 2f with aisan carb ...been searching the thousands of pages for timing and carb tune...haven’t found much specific to my symptoms,so first things first if I could clear up some things first
  7. Cody Quesnelle

    Is it possible the Birfield/outer axle is 15mm to short?1976 fj40

    So ...I’m wondering if it is possible the p.o switched out a Birfield for one that is 15 mm to short ?what is the length of outer axle 1976 fj40 ?just finished the short side (no problems)or I would compare...lol.now I don’t recall removing c clip when I took apart.....classic me.And only have...
  8. Cody Quesnelle

    Stock fj40 coil resistor ohms?

    Looking for a replacement resistor for 1976 fj40 ...what ohm resistor would I need to match stock resistor?napa sells resistors from .8 to 1.8...
  9. Cody Quesnelle

    Carter 4070 fuel pump mounting locations ...1976 fj40

    Got my carter 4070 fuel pump today....looking for good ideas on where to mount it .....and any thoughts on install that may help me ....thanks
  10. Cody Quesnelle

    Anybody worried about there electric fuel pump continuing to run after a roll over or accident?

    So spent a few hour last night trying to decide between electric fuel pump or mechanical, it appears my 40 is running both,from what I’ve been reading dosnt seem like a great idea due to if your mechanical pump fails your electric pump will pour gas into engine.this brought me to a scary thought...
  11. Cody Quesnelle

    Does anybody use there 40s for daily driver?

    Hey just wondering if anybody uses there ol Toyota for daily driver....just sold both my cars...with the plan to keep my 40 to get me from point a to b
  12. Cody Quesnelle

    Does any body want a welded 3rd member?

    Any body want a Welded 3rd pulled from the rear of a fj40 ?look like a decent welding job ...I live in Calgary Alberta
  13. Cody Quesnelle

    Another guy asking about reverse light switch...sorry😬 how does the switch get power?

    So I’ve searched for couple hours ....I haven’t found a straight answer ....ok two wires come from the switch....this is where I get conflicting stories....I’m told that one of the two wires will be hot the other becomes hot when switch is in reverse .the only thing that makes sense to me is...
  14. Cody Quesnelle

    Snorkel ID....

    Does anybody recognize this guy ?stock?aft market?value?is any body interested?i live in Calgary AB
  15. Cody Quesnelle

    Spindle bushing mangled ....why?

    So as promised I gave a solid attempt to finding reasons for my spindle bushing damage ....can’t really find anything....I assume not a common problem.does anybody have an idea what would cause this damage,it only happened to the one side.what is the function of this little brass guy?if not a...
  16. Cody Quesnelle

    Some questions about knuckle rebuild.

    Hey everyone.so close to getting the 40 Rollin ...so im pretty new to wrenching on old Toyota’s ....I got to admit,I tried to search out the answers myself but kinda running out of time before my trip...sooo any tips on removing hub bearing ?kinda doesn’t look possible......the brass thingy on...
  17. Cody Quesnelle

    Ha oh

    It’s Been a good year with my 4o on ih8mud ....and no body has complained about my bezel being upside down......not sure if I hate it ....almost looks better fat side down.How much is this going to annoy people?is it worth it just to be different?
  18. Cody Quesnelle

    fj40 tire racks.......stock or not?

    was hoping to gain a little knowledge on the stock tire racks for fj40...not sure if im into paying what people are wanting for ol rusty ...any thoughts on stock vs aftermarket. not to concerned with staying stock ,just something that won't leave my tire on the road...my 40 came with a rack...
  19. Cody Quesnelle

    Are my brake cylinders supposed to mount on a slope

    So does this look normal ?the rear cylinder mounts a good bit lower than the front
  20. Cody Quesnelle

    A stupid question about rear drum brake cylinders

    Sooo little confused ...pulled the drums off my 1976 fj40 and noticed the brake cylinders are oriented front and back but when ordering cylinders for 76 fj40 they are labeled as top and bottom....most photos of rear drums are oriented top and bottom....yea not a drum brake guy any insight would help
Back
Top Bottom