Search results for query: *

  • Users: Dizzy
  • Order by date

Forum search Google search

  1. Dizzy

    What have you done to your Land Cruiser this week?

    Right, the vapor pressure of ethanol has got to have some kind of influence.
  2. Dizzy

    Turn signal/Flasher issue

    The wattage/code was listed at RockAuto. Then, you can go to any auto store with that information. Many try to make LED flash, but, they don't run hot enough to make the flasher unit click. If you can't pull a minimum wattage/amperage from the switches, points inside the clicker, or harness...
  3. Dizzy

    Grocery getting

    Install a holder for jerry cans. Maybe a spare tire swing-out type spare tire situation to hold them. Slice the tops off, and install hinges/locks on the cans. Ovoid buying lettuce until it is above 32*F. Don't cut into anything with gas fumes still in it. When I was in your situation, I...
  4. Dizzy

    What are these screws for?

    The stamp used on that piece is different than in my '75 floor, from the top.
  5. Dizzy

    What are these screws for?

    interesting
  6. Dizzy

    Turn signal/Flasher issue

    The fourth photo in post #17 needs harness wrap/tape, and a grommet.
  7. Dizzy

    Turn signal/Flasher issue

    Post #7 I'm fairly certain that some of those lamps above are not supposed to flash. Just the ones on the fender pointing forward, and the ones on the rear bumper? That blue crimp 'ring' connector looks like you struggled. For that wire, it would have been easier if it was a 16 to 18g (red)...
  8. Dizzy

    What have you done to your Land Cruiser this week?

    Yes, just south of Canoncito.
  9. Dizzy

    What have you done to your Land Cruiser this week?

    I took it to what I call, 'Chivington's Trail.' I went looking at rocks, but, this is the ambush-track where the Confederates lost the West. It really isn't historic, but, it is as close as I can get without wheeling on private land. A cheap Samsung phone, and an even cheaper clip-on...
  10. Dizzy

    What have you done to your Land Cruiser this week?

    Checked the pressure in four tires. One was about 13lbs.
  11. Dizzy

    What have you done to your Land Cruiser this week?

    They say that a fusible link should be two sizes smaller than the wire it protects. So, I'm not sure if that means to run a 16g fusible link to protect a 12g, or 14g connection to the battery +. But, you get the idea. If a throttle shaft gets loose in the carb, then the throttle blade may...
  12. Dizzy

    What have you done to your Land Cruiser this week?

    Cylinder #5 I cleaned it about seven or eight months ago... This is my 2F's regular routine. Cold starts begin with just a mild to not perceivable, "the-the-the-the" If that lasts beyond warm-up, it is overdue for a cleaning. Number 4 is kinda dirty as well. All cleaned up, a black steel...
  13. Dizzy

    What have you done to your Land Cruiser this week?

    My carb drools gasoline when at rest. It flows thru the intake manifold micro crack, and thru threads on the BTB / Man-A-Fre products plate that is under it. Gasoline can get thru most anything, not hermetically sealed, but, for all realistic purposes, I'd not worry about it. Carbs that have...
  14. Dizzy

    SOLD Atlanta GA - Besttop bikini top, just in time for winter!

    Running a bikini top in winter is some of my best memories...
  15. Dizzy

    Bellcrank Reproduction

    Awesome. Thank you MoCoNative. If you can post a photo or two, I'd be delighted. I had no clue that the air horn would work with the older air cleaner assembly, so that is good news.
  16. Dizzy

    Bellcrank Reproduction

    Yes, a good source for cable sheath would be desired. Could it do 3mm braided cable?
  17. Dizzy

    Bellcrank Reproduction

    The choke cable stop sounds interesting, However, as a child, I bailed my dad out twice, once we were in the mountains fishing, on his '66 Barracuda with bicycle cable. 1.5mm diameter cable for throttle is a joke in my mind, and I wouldn't want to get the throttle cable hot in any uncontrolled...
  18. Dizzy

    Bellcrank Reproduction

    @ToyotaMatt 39.75mm is about what I have on my OEM part between the center of the spindle, and the surface where the cable rests.
  19. Dizzy

    Bellcrank Reproduction

    @ToyotaMatt Do you know the radius, from where the cable rests (about) to the center of the threaded spindle?
  20. Dizzy

    Wanted Brackets for Securing Hand Engine Crank to Driver's-Side Fender Well

    Tub isn't pristine, in my case. It will be a fabricated crank handle too. I'll figure it out.
Back
Top Bottom