Search results for query: *

  • Users: Marn0
  • Order by date

Forum search Google search

  1. Marn0

    Anyone extend the driver's seat in a late model 40 ?

    I did mine by adding another set of rails (on another seat) to the existing rails. Its a little bit higher but I like that. Seat is now back against the wheel well and I have plenty of room. Also moved the passenger seat back using 25*50 unistrut
  2. Marn0

    B to 15B-F swap

    Thankyou. Much appreciated
  3. Marn0

    B to 15B-F swap

    Thread dig. Did this flywheel fit with the 4 speed cast bell housing? Im looking to do this conversion and am struggling to find a 330mm flywheel 8 bolt. Thanks!
  4. Marn0

    Builds Mouldy Mario gets defoliated.

    Holy s*** yeah!!! Been hanging for some updates on OZs best restored cruiser! Was nearly searching the Obituaries for Moldy Mario!!!!!
  5. Marn0

    Rear main seal leak in 77 fj40

    The BJ 40 rear main can easily be changed without pulling any main caps. Remove the gearbox, clutch and flywheel to gain access. Change any suspect bearings while its apart. I also recommend changing the gearbox input seal while the box is out
  6. Marn0

    72 FJ40 converted to a 3B

    3B will be S l oooooo w
  7. Marn0

    B Crankshaft

    I have a good B bottom end here in Aus you can have for free
  8. Marn0

    F engine alternator swap

    Finding an alternator bracket from a newer f engine would probably be the go then it would mount in the same spot
  9. Marn0

    BJ40 Rearend Identification

    So there was fine spline semi floaters then?
  10. Marn0

    BJ40 Rearend Identification

    Didn't the rear inspection cover disappear with the coarse spline axles?
  11. Marn0

    1979 BJ40 Starter

    I could not get an exact match for my 1979 B starter either. In the end I had to get the only one that was available and make it fit. This involved removing the top mounting stud and replacing it with an 8mm bolt. The holes do not line up and 8mm is the biggest I could fit in there. Do the big...
  12. Marn0

    65 fj40 complete all original engine engine

    I have seen SD40 carbs advertised for $1500 here in aus. Parts for these are becoming expensive
  13. Marn0

    Anybody know of a build thread with someone fabricating the entire tub of an FJ?

    Theres a bloke in OZ on facebook that appears to be making his own styleside tub identical to a factory one. doing it all himself and it looks like it came out of the toyota factory. Cant remember his name tho so this info is probably completely useless:confused:
  14. Marn0

    Value Opinion Requested for BJ40

    Half of what it was before the paintjob
  15. Marn0

    Guage cluster ground

    Get a multimeter, put it on continuity and go from the earth pin to the cluster frame and see if there is a connection
  16. Marn0

    FJ40 3speed to 4speed Clutch Problems... HELP!

    Back off the adjustment between the pedal and master. This will allow more piston travel therefore pushing more fluid. Maybe.
  17. Marn0

    What have you done to your Land Cruiser this week?

    Thanks for the info guys!
  18. Marn0

    What have you done to your Land Cruiser this week?

    Where did you get the mirrors from? Also do they have metal mounts or plastic? Thanks
  19. Marn0

    What have you done to your Land Cruiser this week?

    Took it to the lake for a swim
  20. Marn0

    Starter Fluid Makes RPM Go Down?

    POSSIBLY. Just possibly it is allready running lean. usually an engine will increase in revs as it gets leaner. The starter fluid leaking in may be richening the mixture and dropping the revs. Thats just a theory though and happy to be proven wrong- its all about learning
Back
Top Bottom