Search results for query: *

Forum search Google search

  1. T

    intake manifolds

    does anyone know of an aftermarket intake manifold for a 2f. i have heard of one, but i can't seem to rember the name...
  2. T

    camshaft bearings

    what is the exact removal and reinstall for the camshaft bearings on a 2f engine? i have worn out bearings, which are causing a loss (none at all) of oil pressure to the top of the engine. what will i need to do? is it a good idea to change the camshaft as well?
  3. T

    v8 700r and driveshafts

    i've been reading over some of the posts and have found that quite a few people have made mods to the drive shafts. with a 350, 700r, and an adapter from sor, will i be able to keep all the stock drive shaft lengths? in other words, will i have to modify things behind the xfer case?
  4. T

    brake lines

    i am having trouble finding brake lines to fit my 75 cruiser. what i am thinking of doing is taping them out to a larger size. will this work? will the flange meet the calipers and the master cylinder if i tap the union and to a larger size? just to make this clear, i will be drilling a larger...
  5. T

    oil pumps

    i have an oil pump on my 75 that i think is going out... the pump is supposed to be new, however, the heads are not getting any oil. furthermore, the pump never produces more than 25% max pressure on the gauge in the dash. the gauge and sender are new. when the vehicle is cold, the gauge reads...
  6. T

    oil to head?

    i don't think i am getting any oil to my head! i took off the entire rocker assembly, cleaned it, and put it back into place. there doesn't seem to be any oil seeping out of any of the wheep holes in the rockers. i am correct in assuming oil should be coming from these holes, right? what should...
  7. T

    oil on the spark plugs

    i went for a little drive last night, and all of a sudden the cruiser started missing. so i checked a couple of things... and found oil on one of the spark plugs (lots of it.) it is my understanding that oil ON the plug means a valve guide is leaking. is this correct or could it be a ring?
  8. T

    fuel gauges and more

    as far as i know, most of the fj40s have a three post fuel gauge. one for power, one for the sending unit, and one that gives power to the thermostat. on the inside, there are two thermo "blades" one acts to measure fuel, the other acts as a switch and even has an adjustment screw on it. my...
  9. T

    pushrods

    i recently had the #6 exhaust pushrod go out. can i replace just the pushrod, or do i need to replace the pushrod, rocker, and lifter?
  10. T

    blower resistor

    does anyone know the resistance and wattage of the resister on the fan blower? i have been told that it is a 1 ohm 50 watt resistor. is this correct?
  11. T

    driveshaft

    i am sure that this has been asked time and time again, but does anyone think that i will need a longer drive shaft with a 4 inch ccot lift kit? is there anything else that i will need to pay attention to?
  12. T

    curiser charging

    if i wanted to see if the alternator is producing power by using the built in gauge (the one on the instrument cluster) how would i go about doing that? the gauge has a pos and a neg terminal... do i hook up the alternator to the negative terminal and the positive battery post to the positive...
  13. T

    connectors and wires

    does anyone know how to disconnect (take out) the metal connectors inside the electrical sockets. i don't want to have to splice the wires; i want to take them out and replace the entire connector, but keep the original plug.
  14. T

    electrical

    does anyone know how to take off the light switch on the dash?
  15. T

    fj40 32/36 weber

    i have a 32/36 weber on a 2f that i have been having trouble with for some time, now. i have limited all of the symptoms and problems down to the carburetor: it all started with the engine running rough until it warmed up, and, even then, it would still hesitate and misfire through the carb. i...
  16. T

    brake lines and such

    hi, guys. i'm tring to find what i will need to replace the brake lines on my 75 cruiser. does anyone know the size of the fittings, or will i have to replace them with ones from sor or something like that? i don't know if i can use simple compression fittings. does anyone know if this will...
  17. T

    to carb or not to carb

    09/75 fj-40 I-6cyl edelbrock headers (SOR mfg) mallory distributor weber 38mm DGES carburetor stock intake stock heads stock short block no emmissions systems except for the pcv valve etc. i have a 75 cruiser that i've been fighting with for about six months now and just can't seem to get the...
Back
Top Bottom