Search results for query: *

  • Users: PaulGrant
  • Content: Threads
  • Order by date

Forum search Google search

  1. PaulGrant

    Strange noise from sump area

    Hi there, Lately I have noticed a knocking type sound coming from my 1PZ motor (1990). I used a stethoscope on the sump but it was not that profound. However the closer I got to the pulley wheel the more profound it became. I then noticed that the main pulley (one with double belts) was...
  2. PaulGrant

    9kg gas bottle mount suggestions

    I am contemplating mounting a 9kg gas bottle to my SWB 1990 70 series cruiser using a standard gas bottle mount (image below) but I just cannot figure out where, firstly it is possible (support etc) and secondly where it is legal (i.e. does not protrude out from the side to take out cyclists on...
  3. PaulGrant

    Rear shackles removal

    Hi there, I am attempting to replace my PZJ70 1990 SWB cruiser rear shackles and just cannot remove the 2 rear shackles as they are being blocked by the fuel tank. See attached photos.
  4. PaulGrant

    Tie rod total length

    Hi there, I am busy replacing all my tie rod ends as well as my steering damper on my PZJ70 cruiser. When I removed my tie rod I measured it and it was 1213mm instead of the recommended length of 1267mm. I then thought that perhaps my toe in was large so I measured the distance between the...
  5. PaulGrant

    Wanted  PZJ70 3.5L engine radiator top hose

    Hi there, I believe the top radiator hose for the PZJ70 engine has been discontinued. Does anyone know where I can get a replacement part from in Australia or NZ?
  6. PaulGrant

    Immobilising a PZJ70 1989 cruiser

    Hi there, I am keen to understand what is the best manual way of immobilising a 1989 PZJ70 land cruiser. I have previously removed the main fuses but the engine was still able to start!!! Any immobilisers out there that you recommend?
  7. PaulGrant

    70 Series 4x4 operation (hubs, buttons, switches etc.)

    Hi there guys, This may seem like a silly question since one would assume that if you own a 4x4 then you should have all of this under your belt. I just cannot figure this out since my truck has manual locking hubs. My truck has manual locking hubs. It also has the 'HUB LOCK' switch. I also...
  8. PaulGrant

    Oil Pressure gauge not working

    Hi Guys, I have an oil pressure gauge that is not working. I have purchased a new oil pressure sender and installed it. When I inserted the clip back onto the sender and tested it the gauge still did not work. I also checked all my fuses. I then noticed another clip on the same cable that...
  9. PaulGrant

    Rear Brakes shoes keeping tightening

    Hi there guys, I am have some issues with my cruisers rear brakes. I have adjusted the adjuster rods to allow me to free wheel spin the wheels about 2 full revolutions. Sweet as! I then go cruising. Now the mechanism in the drum works in such a way that each time the handbrake is engaged a...
  10. PaulGrant

    70 Series one-piece hub??

    Hi there guys, I am embarking on replacing my 70 series PZJ70 1990 front rotors. I bought the rotors before I took them off. The company I bought them from assured me that they would fit. When I took the front rotor off I tried to remove the hub from the rotor and walked into a wall! From...
  11. PaulGrant

    1990 Cruiser 70 Series Toolkit content

    Hi folks, Can someone please tell me what the following items are and used for in my toolkit.
  12. PaulGrant

    Turbo kit and vendor for 1PZ engine

    Hi there fellas, I have searched this forum regarding this question and have found some very old threads. What type and make of turbo can I fit to a 1PZ engine? Is it a straight out of the box fitment or do I have to manufacture/beg/borrow/steal a special flange to mate the turbo to the engine?
  13. PaulGrant

    Engine oil for PZJ70

    Hi fellas, I am new to this forum so please excuse me should I break any forum rules. I have read the guidelines so I will try my best. I have recently purchased a 1990 Land Cruiser with a 1PZ engine. My question is what is the recommended oil BRAND that I should purchase. I will stick with...
Back
Top Bottom