Search results for query: *

Forum search Google search

  1. 71cruiser71

    Looking for someone to make me part please

    Hey wondering if there is anyone out there who can weld and have some time to make me a part out of steel please. I'm looking for an all steel back lift gate door handle for 72' 40 Mine keeps breaking on the flange I can send pics later
  2. 71cruiser71

    Wanted  2f crank pulley, 3 groove

    Looking for 3 groove crank pulley for 2f. Motor is from 87 fj60
  3. 71cruiser71

    Noise found; crank pulley. Solution?

    This just started recently, and it sounds like something is loose inside the motor? I can't really pinpoint it, maybe a water pump? I haven't enough experience with bad water pump? I really don't know, thoughts?
  4. 71cruiser71

    Wanted  Warm pull cable

    Looking for heater shutoff valve warm pull cable and knob please. Mid 70s or whatever fits
  5. 71cruiser71

    Adding heater shut off valve

    Hello, I want to add this heater core shut off valve for my 11/71. The original F motor had a manual shutoff valve on the driver's side head. I now have a 2F from an 87' 60s. I want to have the knob pull shutoff valve seen below from Genuine OEM NipponDenso TOYOTA Land Cruiser Valve Assy...
  6. 71cruiser71

    SOLD  Rear swing up door striker

    Looking for the side panel metal striker for hard top #27 in this picture. Just need one thank you
  7. 71cruiser71

    New brake master cylinder to old wiring

    Is it possible to connect this brake master cylinder wiring into my old wiring harness and back to my red brake warning light?
  8. 71cruiser71

    Wanted  Rubber insulator piece for fj40 horn switch

    I remember seeing a thread where someone made a bunch of horn parts, including the rubber piece. Anybody know of anyone who made the rubber piece. Thanks, it's the only piece I need
  9. 71cruiser71

    SOLD  Voltage regulator 58-9/72

    Oem remanufactured external voltage regulator. Never installed. 30$ shipped lower 48 But will ship anywhere for additional shipping costs
  10. 71cruiser71

    Maybe an easy question about guages

    So my recently rebuilt 2f (from an 87` 60) has this low oil pressure reading. It never goes higher than the middle even under higher rpms. It usually stays right above the second tick. and also I think my guage cluster is reading temperature incorrectly because when I shut off it falls to H and...
  11. 71cruiser71

    Wanted  Wtb, 11/71 turn signal switch

    4 pin connector I believe, I can't afford a new one and I hope to be putting power steering in in the future and want to change the coloumn. Anyone I need turn signals hmu
  12. 71cruiser71

    Wanted  Wtb-LF fj40 rear door handle bolts

    Looking for fj40 rear door handle bolts. For exterior lift gate handle 2bolts that connect the handle and allow to pull handle open but still stay connected. Please dm or asked for more info I will post a pic if I can find one
  13. 71cruiser71

    How much would you sell your truck for?

    I get this question every so often.... and I always have to think really hard about it. And I can never come up with a number that sounds right, I always end up saying NFS. If a person with a brief case full of $$, came up to you and asked how much to sell... how much would you sell it for...
  14. 71cruiser71

    Quick question- 12v plug per fuse

    Hey all, maybe someone can answer this question for me, how many 12v accessory plugs should I be using per fuse position. I see a lot of diagrams and info showing you can piggy back 12v plugs off of each other but also saying you shouldn't do that. I am installing 3- 12v plugs on my dash. 2...
  15. 71cruiser71

    11/71 new voltage regulator wiring question

    Hello, its been a long time since I've last posted. I tried searching but couldnt find this. I got a new voltage regulator but I notice my old one doesn't have one of the prongs connected to anything. Im assuming its the ground to the alternator? Should there be something connected? Should I add...
  16. 71cruiser71

    Cant seem to dial it in

    Hello, So I am having troubles "dialing in" my 87 2f motor from a 60 series. (Its in a 72' 40series) it is currently my daily driver right now, as I dont have anything else now. I just started driving it about a week It's kind of a long story, but to make it short... my dad thought it would be...
  17. 71cruiser71

    For Sale  Arb bumper fj40

    Hey everyone, Selling this new ARB front bumper for fj40. Never seen use, but it's been sitting installed on my truck for a couple months. It's a little dusty but no scratches or dings Asking 600$ I'm located in northern California. Any questions let me know
  18. 71cruiser71

    Brake booster?

    It's been a couple of years since I have been on here... please forgive my ignorance. My truck has had some problems over the years and have been slowly fixing them. Since I can remember I have always had a problem with my brake pedal not coming back after being pressed. I would have to pull up...
  19. 71cruiser71

    Distributor spring, and vacuum info needed

    It's been a couple of years since I have been on here... please forgive my ignorance My 87 2f has been desmogged. Is that guy Jim still respringing distributors? Anyone know how I can get in contact with him please. Also I am missing a little vacuum valve (I forget what it's called vsv or...
  20. 71cruiser71

    Running "rough" after 2 year sit

    Hello, i have been out of the game for awhile here, so any help is appreciated. I have a 72' , 40 series. It has a desmoged 2F from an 87', 60 series. But i havent respringed or whatever it is the distrubutor. So i put the distrubutor from the old F motor on it. It has electric ignition on it...
Back
Top Bottom