Search results for query: *

Forum search Google search

  1. thepinktaco

    For Sale  MA - FZJ80 Axles

    Front and rear FZJ80 axles. Swapped elocker diffs to my 80. The front was disassembled as I was going to convert the housing but ended up cleaning up the elocker housing instead. The rear axle is a bit rusty and is the elocker housing so has the cutout for the locker motor. Front axle and both...
  2. thepinktaco

    FJ40 Energy Body Mount kit

    Black poly body mount kit for FJ40. One of the nut plates was missing so I made one. Looks like all the mounts are there. $80 shipped.
  3. thepinktaco

    ABS sensor dummy plug

    I have a FF Elocker axle that I just put into the rear of my Tacoma, not running abs and I think I threw the sensors out by mistake. Did they come without ABS and have a dummy plug where the sensor goes? On the tacoma elockers without abs they had a plug that bolts in place of the sensor...
  4. thepinktaco

    Summit radiator to 350 lower hose

    What hose works good with a 350 and Summit radiator. I bent up a coat hanger but couldnt find one at the local parts store. Its hard to find one that fits when the outlet of the radiator is higher than the output of the waterpump.
  5. thepinktaco

    Summit radiator mounting

    Started making mounts for the summit radiator going into my 40. Looked at a bunch of different mounts, and it seems as everyone is mounting them differently. I ended up bending some aluminum strap to fit between the radiator on the bottom. I was planning on riveting them to the radiator then...
  6. thepinktaco

    FF hub dowels

    I have an axle all disassembled and going thorough everything before it goes into the rear of my tacoma. On the rear shaft I have heard of the studs breaking off. Since there are only 2 dowels in the hub/shaft I was thinking on adding a few more dowels, like the setup for the fronts that...
  7. thepinktaco

    Walker 42087 flange

    Anyone know a part number for the male flange for the exit of the y-pipe. Going to make my exhaust but can find the other half of the flange that bolts to the y-pipe, walker 42087.
  8. thepinktaco

    Gas tank diementions

    What are the rough diementions of the under seat gas tank? The tub I have had the floors replaced with diamond plate and whenever the guy did it they didnt make a recess in the floor for the factory tank. I have to buy a tank anyways so I was thinking on just buying a fuel cell and putting it...
  9. thepinktaco

    Steering shaft support bearing

    Some good info for the FAQ... Putting a 60 p/s box into my FJ and I knew I needed a support bearing for the steering shaft. I know you can order them from some companies but I really was looking to get one sooner. A quick simple search on Google found a common bearing that is the same size...
  10. thepinktaco

    FJ60 power steering with mini discs

    Getting ready to install a 60 ps box in my 40 and swap the front drums with discs from a mini axle. Still going to be SUA so highsteer is out. Im trying to figure out the steering linkage. The 40 TREs are smaller than the p/u I believe and a standard TRE wont fit in the 60 arm you need to use...
  11. thepinktaco

    transfer case crossmembers

    I need to make a new transfer case crossmember and want to make something like treeroots xmember but have the factory 4 speed so the shaft sticks out of the back of the case. Anyone make a x-member like this one with a factory trans? Or what other ideas are out there? I have the advanced...
  12. thepinktaco

    frenched front hanger with shackle reversal

    Planning on doing a SOA and shackle reversal on a chassis that I have. Trying to keep it low with the shackle hangar through the frame and was thinking on cutting the front frame horn and making frenched spring hanger for the front. Anyone done it this way? only problem i could see is steering...
  13. thepinktaco

    Frame, cowl, half rotted 3/4 tub, 3-speed case

    Located in Montague, MA. Possible local delivery for alittle extra 71 frame, motor mounts and ps bracket removed. Bought another chassis with a tub so I dont need this one. I can take the motor mounts and p/s bracket off the frame Im using if wanted. No rot, clean frame. $400, rolling chassis...
  14. thepinktaco

    A-pillar rust repair

    The bottom a-pillar on the cowl im repairing is rotted beyond repair on the drivers side. I made a piece that looked good except I didnt realize that it tapers to about 3 inches on the bottom where the rockers bolt to. Anyone make a complete new piece? Im trying to figure out how to make one...
  15. thepinktaco

    Wanted  Need a spare FJ80 birf

    The axle I have is an ABS axle. Drivers birf is starting to click in reverse so I would like a trail spare.
  16. thepinktaco

    Sill corner templates

    Anyone have templates for the corner supports that are part of the rear sill? I have a tub that the sill and corners are missing on so I have nothing to go by,
  17. thepinktaco

    Wanted  Rocker panel channel

    Looking for the rocker panel channel for the door seal. Mine is all rusted out and dont want to buy new rockers to get the channel. Someone must be doing a resto and replacing the whole rocker.
  18. thepinktaco

    Anyone make this piece?

    Mine are alittle rotted and I noticed that CCOTs rockers dont come with them. I saw real steel has the 1/4 panel upper lip but they dont have what I need.
  19. thepinktaco

    Whos got the 45 in Greenfield?

    Saw a 45 with a wooden bed or a cut 40 with a bed drive by the shop today. I only caught it out of the corner of my eye but it was blue. Ive been told about it driving around but dont know whos got it.
  20. thepinktaco

    SOA hight to bottom of door

    Just wondering what the height is to the bottom of the door on some SOA 40's. Trying to get an idea for when I actually get to working on my FJ. Other specs and pics would be helpfull/
Back
Top Bottom