Looking for the early 40series (63ish to 67) rear view mirror with the 3bolt mount--complete or just the mount. This is for a 67fj45, so technically the -60020 version, but I could also make the previous -60011 work.
Looking for an early (1980 model year and older) H41 4spd transmission. This would have a 16spl output shaft and would have been attached to a single piece t-case. Doesn't matter which input shaft (gas or diesel). The input shaft would have 22teeth and a 1st gear ratio of 4.925.
A very...
The question concerns adding width to the WMS to WMS when converting a drum front axle to disc brakes. Some of the companies selling bolt-on caliper brackets specify the increase in front axle width with their products. I am not using the add-a-bracket--I am using fj60 and/or minitruck...
I've done the searching, looked at builds, read the disc brake conversion writeups, peered over the archives, and studied my service manuals. Toyota has never published knuckle ball or knuckle dimensions/specs . The two outfits currently manufacturing knuckle balls (or bells) don't share any...
Looking for the centered rear axle from a 60-62 fj40 (not fj25). I could also use just the front or rear differential from the same. Will pay shipping to Nevada.
I have a 2000/2001 14B engine from a Bandeirante being transplanted into an FJ43. On the fuel injection pump, there is a 3-pin harness that disappears into the pump. One of the circuits is for the fuel shutoff solenoid, but I seem to recall that one of the leads is for the tachometer...
I am looking for the tubular seat frame for the passenger bench seat (over the fuel tank) from an early fj40, 1972 and down. I really only need the bottom part of the frame.
I need a set of rear brakes--backing plates, internal hardware, and drums--from a FJ60/62 or 81+ FJ40. Must be in good shape, ie not bent, mangled, or rusted out. Thanks
Looking for a fine-spline transmission input shaft, 33311-60080, as found in the 8/80-10/85 BJ diesel series
(it has the smaller diameter, open input bearing)
I need a good pair of driveshafts. The T-case ends I need have the 11mm bolts and has the 66mm SQUARE mounting bolt pattern on a circular flange. I'm not sure what model, but it would be from about 1986 to 1987 to match the T-case.
Location: Las Vegas, NV
I need a fj60/62 rear axle housing (mostly for the outer flange ends) for a project. The outer ends are preferred, or the bare housing (center 3rd portion condition not important).
I would also be interested in a complete FJ62 rear axle.
Thanks
Location--Las Vegas, NV
I am looking for a 40/45 series rear axle, 1981-1986 for the external parking brakes. A complete axle will do, or without the 3rd member or axle shafts, but the brake systems must be complete. Thanks
I am searching for a good, 24 volt, oil pressure gauge for a 84bj42, part number 83510-60051. Anything from 1979 to 1984 is the same part. I would also take the entire instrument cluster with a good oil gauge. Thanks.
The oil pressure gauge on my 84bj42 just fried and the instrument repair shop says that it can't be repaired.
I have tried to find a new one worldwide and have had no luck. The part I need is a 83510-60051, oil pressure gauge, receiver, 24volt, 1/79-10/84. BTW, the senders are still available...
Would anyone know the correct mounting location of the main bonding cable (frame to engine) on a 84BJ42? Searching has yielding no help nor has the wiring diagram.
New aluminum diamond plate quarter panels for 10/69 to 84 40series with the rear side marker lights. SOR part number 238-69. New and unused, they have been lying around the garage for several years. I have lost the rear flat piece, but I will include it if I can find it.
$50 plus...