Update...
Thanks toy_tek for your response. It helped alot. I understand the wiring diagram now. I found the oil sender (see pic) and there is a stub of a yellow/red wire on it. I also found the yellow/red wire (see pic) that was cut from the harness and was able to confirm continuity from...
Hello everyone,
I'm working on getting my amp and oil pressure gauges working and need some assistance as I'm electrically challenged. These are the gauges that reside above the shifters on my '79. I'm thinkin that they are just not hooked up. The idiot lights on the main dash panel work...
I would recommend 3 psi. It’s probably best to get the regulator and a gauge so you know exactly what pressure you are providing. Here is my setup as an example. I’m running the Weber 32/36.
Thanks for the input. I got the heat shield off and had a look. There are supposed to be 7 studs holding the manifold on and sure enough there is no stud back by cylinder #4 where I was feeling the exhaust air. Also, as is usually the case, looks like someone has been in here before as I...
I've been tracking down/fixing some exhaust leaks and now I have come to the primary leak. When I hold my hand up against the heat shield I can feel exhaust air coming out a couple of the open ports (see pic), so I assume I need to replace the exhaust manifold gasket. I've done some research...
You’re killing it with the videos. Puts a smile on my face with each update. Now that she’s made her first trash run I think she’s ready for a car show. That old truck is sure to get more attention than any concours restoration.
Just wanted to comment how much I enjoy this forum and the knowledge that is here. My heater blower has never worked on Low since I got my '79. I found this thread in a matter of minutes and pulled my heater blower resistor out. Sure enough, one of the coils is broken (see pic). Found the...
I would think that your leak is transmission fluid. There is is probably a bad oil seal where the shifter shaft goes into that side case in front of the deteriorated boot you have circled in red on your picture.
No worries. Thanks for looking. I'll keep an eye out for one. I've never been, but I may take a trip to a salvage yard. Anybody know of any good yards that have these old trucks in the Dallas area?
Well, good news and bad. Good news is that I've diagnosed where the problem is. Bad news is that it is the switch. I tested continuity from the wiring harness (see pic) back to the switch and I have NO continuity when the button is pressed. I then tested continuity from the wiring harness...
Per your suggestion, gnob, I used the 10V off the plug and connected ground to the other lead on the pump and the pump does work. So I need to check the switch. I can test for continuity or maybe just clean the connections on the stalk switch first. How does that stalk come apart? Does the...
No, I am not pushing the washer button. I just have key on and measuring for 12 volts on the blue wire. Key off = 0V, Key on = 10.4 volts checking at front and rear of connector.
Ok, with key on and voltmeter connected to negative terminal of battery and blue wire on pump plug I am getting 10.4V. Seems like that should be showing 12V?
You'll have to dumb it down for me gnob. I see that same diagram in the FSM. All my tests have been with the key in the on position. Not sure if this matters, but the washer pump is not the original and is just a universal pump/washer tank.
Let me just say I'm really, really out of my element when it comes to electrical. Ok, I have a 1979 pickup and I'm trying to figure out why my washer pump is not working when activating the switch. Here is what I have done so far.
- the windshield wipers work on all three settings...
Well Pappy, I ended up having to use just the black spacer. The green seat was still too thick. The shifter isn't perfect, but it is definitely better. Those retainer bushings that you pointed out are part number 33615 that you see on the parts diagram that I attached. I got some of those as...
Hello Everyone,
My shifter was very sloppy so after researching here, there are alot of posts indicating to replace the shifter seat and shifter lever bushing. I've got the correct lever bushing and I ordered part number 33505-35020, but this can't be the correct seat for the L43 side mounted...