I’m wondering if anyone has knowledge on how deep the rear license plate panel on a GX470 is. I’m thinking of using some Rigid Industries flush mount LED’s to do a “stock” or “well-blended-in” look for some rear lighting. Chime in please because I’m too scared to cut without being sure it will...
What’s the consensus on the pair valve? Keep it or delete? I have a ‘94 with a considerable vacuum leak that I traced down to (I believe) the pair valve at this point, my LC will not pass emissions and the idle is high but NM is not very particular with visual inspections so a delete is an...
Does anyone in NM (ABQ Area) who has the Icon Delta Joint install tool or had experience on installation. I have a ball joint press but not sure if the angled shim is necessary. Any input is much appreciated.
I am having an issue passing emissions, and I’ve done the basics like vacuum lines, tune up, oil change, charcoal canister, etc. Very easy emissions testing in NM but at this point, I’m thinking it’s the Cats but don’t want to throw money at it if I don’t have to. The o2 sensors were replaced...
up for sale is like new set of 5 cooper discoverer HTP. Located in Albuquerque, NM. The tires are practically new and were take-offs from my stock tires after replacing them with MT’s. All 5 tires for $450.
is there a way to get the air out of the air suspension without removing or cutting the air lines? Looking to install a spacer but don’t want to mess with the lines and get any leaks.
Just picked up a 2008 GX470 with 42k miles and looking to start the mods. Suspension is in perfect shape so I’m looking to keep the airbags but lift it 2 inches or so to fit 33’s. Does anyone know where I can find the airbag spacers? I heard AMTS has some but can’t find a retailer that sells...
Can someone let me know the denso part numbers for the o2 sensors on a 1994 FZJ80. Looking to find them on Amazon. Also, any pointers on removing the rounded off nuts? Thinking of buying the Irwin bolt grip bolt removers, unless someone has an easier way.
My 94 80 series was running great and then I started having starting trouble. Battery is a new optima yellow top and the battery clamps are new heavy duty terminals so the battery shouldn't be the problem. I also have a new fusible link installed recently. I removed the old starter and got it...
opportunity to buy fully built trail rig. Front and rear solid axles with arb's and gears set up as a trail rig that is newly built. Contact with any questions.... $9k, all n brand new...
Is there a secret to removing the top frame bolt for the front panhard rod? I got the bottom bolt out but the front is impossible, even with a HD impact gun, mine won't budge a bit. I'm to the point of using a nut splitter but the nut has a flat base so I don't know if the nut splitter will work...
Anyone ever snap an axle knuckle felt wiper bolt? If so, how do I get the broken bolt out without taking the whole knuckle apart again? I was checking the bolts after finishing the job to be sure they were snug and the last bolt I checked snapped off and I really don't want to take it apart...
hey guys, I have a high idle problem and have replaced the TPS, knock sensor (was throwing the knock sensor code) and the temperature sensor. My CEL went away for some time but I still have a high idle (@ 1k-1200 RPM's) and my CEL just came back on throwing code 25 and 26 rich/lean combo. Any...
I have a brand new Icon Vehicle Dynamics caster correction kit. This will adjust 3 degrees of caster for a 3 inch+ lift. Everything is present in the kit including the shop press tool. $100
I also have grey armrests for the doors: all 4 for $50
Rear mud flaps $30 each
Factory radio $35
4 oem...
Hey guys, looking to pull the trigger on the 75mm slinky kit, I just made my mind up between the Slee 6 and the slinky. Just wondering about the caster adjustments and other mods needed to run this kit and if anyone has input. This will be a daily driver and I will be getting the stage 1 and it...
I got a new winch bumper and went to install it but found that my frame is not perfect and the holes don't align so I can only bolt up the driver side of the bumper. I need to move the frame/bumper support on the passenger side over about 1/4-1/2 an inch, should I take it to a body shop or try...
I recently replaced my TPS sensor and rear knock sensor to clear the CEL light on my 1994 Land Cruiser. It cleared the CEL lights for a few days, it's not my daily driver so it doesn't get driven more than once a week yet so it's not cycled much. After changing the TPS, the idle was high (over...