Search results for query: *

Forum search Google search

  1. bw86newman

    alignment after axle rebuild?

    That is what I figured, but just to confirm, separating the tie rod from the lower control arm on the knuckle shouldn't impact the alignment. Thanks.
  2. bw86newman

    Your alarm/unlock remote stops working one day...

    some have a "valet" switch that you press after turning the key to "acc". probably located around driver side kick panel...about a pencil eraser size.
  3. bw86newman

    alignment after axle rebuild?

    when replacing axle seal / rebuilding knuckles, do you need to get an alignment once everything is back together? I will be rebuiding both knuckles and swapping birfs from side to side. Would it make a difference if you did or did not disconnect the tie rods from the lower control arm on the...
  4. bw86newman

    Axle spindle scratch/groove

    the spindle isn't cracked, it is definitely a gouge as a result of something. Like someone took a massive flat head and gouged the crap out of it?? @Tools R Us ...when you say it is worn enough that the seal chamfer is gone, are you referring to at the base of the spindle, the first step...
  5. bw86newman

    engine harness clip?? P/N??

    Tool R Us that looks like the one...checked the thread and that looks right on...thanks guys
  6. bw86newman

    engine harness clip?? P/N??

    does anyone know the part number for this plastic wire harness clip. It has a raised "25" on the back of it. PS against firewall. Thanks.
  7. bw86newman

    Axle spindle scratch/groove

    haven't been having any problems found it while replacing wheel bearings. Do however have some clicking on that side when accelerating up sharp turns in parking garage - preparing to to axle rebuild and swap sides.
  8. bw86newman

    Axle spindle scratch/groove

    What do you guys think?
  9. bw86newman

    Nitto Ridge Grappler 285/76/16 on stock 80

    After - LT285/75/16 Nittos
  10. bw86newman

    Nitto Ridge Grappler 285/76/16 on stock 80

    Before - 275/70/16 Michelins
  11. bw86newman

    Nitto Ridge Grappler 285/76/16 on stock 80

    For anyone who is interested, I just switched out the oem Michelin ltx m/s 275/70/16 with Nitto Ridge Grappler LT285/75/16 on my stock suspension 1995 Land Cruiser. There is no issue with clearance at all (as many other posts have stated in the past). See before and after pictures below. Ride...
  12. bw86newman

    When to perform knuckle rebuild? mileage or year interval

    Here is an update from another thread I have on this topic....thanks for all the inputs
  13. bw86newman

    How do these knuckles look??

    Update...changed the diff oil (see picture below of old oil & magnetic plug)...also added about 6oz of cv grease in each. Will check everything again next weekend. Thanks everyone for the input.
  14. bw86newman

    How do these knuckles look??

    Thanks for the replies. Based off this thread and my other one, I plan on cleaning up both assemblies, check the grease level and add moly along with changing the diff oil. Then see what a week of driving does with clean assemblies. Planning on using Mobil 1 gear oil and sta lube cv joint...
  15. bw86newman

    How do these knuckles look??

    Bought the truck about 6 months ago. Was checking the brake pad wear and snapped some pictures of the knuckles. This is my first car with this setup. Is this normal or does it seem like time for a rebuild? Last knuckle rebuild was 20k ago (8 years ago). First two are driver, second two are...
  16. bw86newman

    When to perform knuckle rebuild? mileage or year interval

    Finally got around to checking the front end....everything seems to be pretty sound as far as the steering/linkages. Below are pictures of the knuckles. (First two should be driver, and second two passenger). What does everyone think of them? Also checked the brake pads and all were right...
  17. bw86newman

    When to perform knuckle rebuild? mileage or year interval

    Thank you all for the replies.....This one has definitely been a "mummy bear hitting the mall" for most its life and will probably continue that way for a while since I live down in Florida (wish there were mountains or even hills here). I will check the steering/suspension play and take some...
  18. bw86newman

    When to perform knuckle rebuild? mileage or year interval

    I recently bought an FZJ80 from the original owner with complete service history going back to 2004. Truck currently has 125k on it and has been a city car/babied all its life. Last knuckle rebuild was only 20,000 miles ago. Although, that was 8 years ago. I plan to take a trip from Florida...
  19. bw86newman

    Antenna Switch Continuity Test

    @TomH are you referring to the wires in this picture? There is a quick connect electrical cable going to a white/silver box with heat sinks on it (left side of pic). Not sure what that is for. The others go into the firewall through a rubber grommet? Is one of these the antenna power that is...
  20. bw86newman

    Antenna Switch Continuity Test

    Thats good to know. Thanks. What year LC do you have? Have you actually accessed the motor assembly plug to test for voltage? Any tips if so?
Back
Top Bottom